Skyblade Turboprop 10' Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 40

Skyblade Turboprop 10' Скачать руководство пользователя страница 30

30

SKYbLADe FANS

-

Where Form Follows Function

9

eLeCTriCAL iNSTALLATioN

For use with manufacturer supplied motor and drive only.

Not for use with other speed control devices.

Pour utilisation avec le moteur fourni par le fabricant et le lecteur uniquement.

Ne pas utiliser avec d’autres appareils de contrôle de vitesse.

To avoid a short circuit, be very careful not to get metal chips in the control.

Pour éviter un court-circuit, faire très attention de ne pas obtenir des copeaux de métal dans le

contrôle.

The SkyBlade Fan product warranty will not cover equipment damage or failure that is caused by improper

installation.

La garantie des produits Skyblade Fan ne couvrira pas les dommages à l’équipement ou de l’échec

qui est causé par une mauvaise installation.

CAUTION/ATTENTION

!

IMPORTANT: Check that the correct input voltage is being sent to the fan. See rating labels on the

motor for acceptable voltage. A blown fan due to incorrect input voltage is NOT covered under

SkyBlade warranty.

WARNING/AVERTISSEMENT

!

!

Exercise caution and common sense when powering the fan. Do not connect the

fan to a damaged or hazardous power source. Do not attempt to resolve electrical

malfunctions or failures on your own. Contact SkyBlade Fans at 1-586-806-5107 if you

have any questions regarding electrical installation of this fan.

Faites preuve de prudence et de bon sens lorsque vous alimentez le ventilateur. Ne

pas brancher le ventilateur à une source d’alimentation endommagé ou dangereux. Ne pas tenter

de résoudre les dysfonctionnements électriques ou des échecs sur votre propre. Contactez Skyblade

fans au 1-586-806-5107 si vous avez des questions concernant l’installation électrique de ce ventilateur.

«
...
28
29
30
31
32
...
»

Содержание Turboprop 10'









































Отзывы:

Нет отзывов