Skyblade Turboprop 10' Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

background image

26

SKYbLADe FANS

-

Where Form Follows Function

Boomerand Bracket (x8)

c

Blade Boomerang Brackets

a

b

8

iNSTALLiNg bLADeS

8.2 Attach Boomerang Brackets:

Attach the Blade Boomerang Brackets using the Blade Hardware. Moving counter-clockwise, position

the Boomerang Brackets as specified.

Hole A & B rests on the blade. Hole C will be positioned on top of the boomerang bracket of the

blade previous. First, install all boomerang brackets and hardware by hand tightening.

Second, tighten the blade bolts individually with a 1/4” allen wrench/hex key.

Blade Hardware Kit (supplied):

a.

(8) Soc Cap 5/16-18 x 5/8

b.

(8) Soc Cap 5/16-18 x 3/4

c.

(16) Zinc Split Lock Washer 5/16

ATTENTION: Upon completion of the mechanical installation of the fan and before powering on, spin

the fan around multiple times by hand to ensure all brackets are clear from contact with other parts

on the fan. Thoroughly inspect the hub, the bolts and brackets within the hub to guarantee clear

and proper rotation. If you find that the fan has a bracket that is hitting another object on the hub,

contact SkyBlade Fan Company for a resolution.

WARNING/AVERTISSEMENT

!

!

Disconnect power to the motor before installing the blades.

Débranchez l’alimentation du moteur avant d’installer les lames.

Do not tighten the bolts until all the blade Boomerang Brackets are attached.

Ne serrez pas les boulons avant d’avoir fixé tous les supports de boomerang de lame.

«
...
24
25
26
27
28
...
»

Содержание Turboprop 10'









































Отзывы:

Нет отзывов

Похожие инструкции для Turboprop 10'

Бренд: Fan-Tastic Vent Страницы: 3

Бренд: Fan Turbine Страницы: 32

Бренд: S&P Страницы: 64

Бренд: ebm-papst Страницы: 11

Бренд: Maico Страницы: 2

Бренд: Kambrook Страницы: 12

Бренд: Xpelair Страницы: 14

Бренд: Midea Страницы: 10

Бренд: Kambrook Страницы: 16

Бренд: Genesis Страницы: 9

Бренд: BLAUBERG Ventilatoren Страницы: 20

Бренд: Faro Barcelona Страницы: 12

Бренд: Xpelair Страницы: 44

Бренд: Vent-Axia Страницы: 12

Бренд: Ayce Страницы: 18

Бренд: Qazqa Страницы: 14

Бренд: Westinghouse Страницы: 28

Бренд: iLiving Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды