SkyAzúl Trimble/LSI GM820, Инструкция по установке и обслуживанию

Страница: 18 / 30

15
SerVice anD inStallation Manual
Motion cut and other lMS inputs
and outputs
Go to menu 5C . Items 1 and 2 are the two LMS
outputs. The LMS indicates if the outputs is
supposed to be in ‘safe’ condition or ‘alarm’
condition. In ‘safe’ condition, a voltage will be
output on the motion cut wire.
Self-test : if the self test indicates Pass , it means
that the display reads back the expected
voltage.
*important: The items #3 and #4 are usually inputs
connected to other equipment, switches or joystick.
The output function may indicate a fail and it is
normal because they are actually inputs in the
default configuration. Access the menu 5E to verify
the status of those two inputs.
For test purposes, it is possible to set the signal of
an output manually, in this screen. To manually
change the output of a wire, select it and press the
enter key. To have a voltage applied on a wire, its
status must be “Safe” and to have 0 volts on it, its
status must be “Alarm”. If the self-test indicates
“Pass”, it means that it reads the expected voltage
level.
connector should have power on wires 10 & 11.
lMS lightbar diagnostic:
The LMS top five light should match the lights on
the pipelayer boom. To set the light bars in a
specific way, look in the table which control wires
should be active.
Example: to light all 5 external lights, the LMS light
bar signals 1 & 3 should be active. Access menu
5C as shown above, turn those two signals to Safe
status, which means havnig votlage. For diagnostic
purposes, the LMS
lMS input signals:
Alternatively to the above, access menu 5e)
digital input to see the status of the two digital
input signals:
No 1 Mute input
Off / On
No 2 Rigging mode input Off / On
System Sensors Diagnostic
1. Go to menu 5a) S
ySteM
S
enSorS
D
iaGnoStic
.
2. Select the sensor and press enter to see the
sensor data in menu 5a1) S
enSor inForMation
.
3. Press exit to return to menu 5a) and select an
other sensor or press exit again to return to the
operation display.
radio network Diagnostic
1. Go to menu 5B2) l
aSt SenSorS receiVeD
.
Sensors are shown with their radio ID number
and the sensor type.
a. Use up and Down to scroll through the list.
b. Press exit to return to menu 5B).
2. Go to menu 5B3) S
earch For SenSorS
.
a. Press enter to launch a sensor search.
3. Go to menu 5B4) B
it error rate teSt
. This test
should only be conducted by technical service
personnel.
4. Press exit to return to the operation display.
Display Diagnostic
1. Go to menu 5D) D
iSplay
D
iaGnoStic
.
1) t
iMe
: current time according to the LMS
internal clock.
2) D
ate
: current date according to the LMS
internal clock.
external light bar Control wires Pin
Green #1 Light bar signal 1 9
Green #1&2 Light bar signal 2 10
Green #1,2&3 Light bar signal 3 11
All amber Light bar signals 1&2 9+10
All 5 lights Light bar signals 1&3 10+11
table: Menu 5c - testing the outputs
1) A2B and Overload Status: Safe
Self-Test: Pass
2) Free swing cut Status: Safe
Self-Test: Pass
3) Mute input Status: Safe
Self-Test: Pass*
4) Rig mode input Status: Safe
Self-Test: Pass*
5) Lightbar 1 Status: Safe
Self-Test: Pass
6) Lightbar 2
Status: Safe
Self-Test: Pass
7) Lightbar 3
Status: Safe
Self-Test: Pass
8) Optional
Status: Safe
Self-Test: Pass
SkyAzul, Equipment Solutions www.skyazul.com 301-371-6126