Skope OD1100N Скачать руководство пользователя страница 48

Страница: 48 / 50

Troubleshooting

Service Manual

SKOPE OD1100N

8 Troubleshooting

Electronic Controller

Alarms signal unexpected operational changes in the fridge. When an alarm is activated, use

the electronic controller app to help diagnose the problem, and service as necessary.

Cabinet and Refrigeration Cartridge

For problems with the cabinet and refrigeration cartridge use the following table.

Table 12: Cabinet and cartridge troubleshooting

Problem

Possible Cause

Recommended Action

• Cabinet not

operating

• No controller

display

• Loss of power supply

• Check mains power supply.

• Loose plug

• Check all plugs are connected correctly.

• Cabinet not

operating as

usual

• Incorrect parameters

Depending on the controller:

• Wellington Drive: Reload the parameter set.

• Dixell: Check each parameter individually. Get the latest

parameter set by registering for and logging into the

skope.com website, or contacting Customer Service.

• Defrost cycle

incorrect length

• Fan not working

• Loose plug

• Check all plugs are connected correctly.

• Lights not on

• Electronic controller is in ‘Night mode’

• Switch the light on while keeping the cabinet in night

mode by pressing the light button on the electronic

controller faceplate.

• Change the cabinet into ‘Day mode’ by pressing and

holding the light button on the electronic controller

faceplate.

• Light switched off/night blind closed

• Switch the light on via the light button on the electronic

controller faceplate, or via the app.

• Open the night blind.

• Failed LED light

• Replace the light.

• Refrigeration system error (indicated by

the electronic controller)

• Diagnose and repair. If a system fault is found contact

SKOPE for information on how to proceed.

• Plug not connected properly

• Check and clean the plugs.

• Power supply fault

• Replace the light’s power supply.

• Light component

not working

• Plug not connected properly

• Check and clean the plug connection in the side light

channel, behind the loom cover.

• Faulty light

• Replace the light.

• Segment of light

not working

• Faulty light

• Replace the light.

• Excess noise

vibration

• Refrigeration pipes transferring

vibration into the cartridge

• Re-align the pipes to ensure they are not touching the

evaporator tub bottom surface, evaporator tub support

legs, plastic base, or condenser coil assembly.

• Excess

compressor noise

• Noise variation is usual as the variable

speed compressor speed changes

• Damaged mountings

• Check the mountings to ensure there is no damage to

the rubber, or the washers, nuts or screws.

• Compressor not

operating

• Compressor electrics

• Check all plug connections and ensure that the

compressor electrics are operating correctly.

• Make sure the compressor is supplied with consistent

voltage over 220 volts.

• Ensure the voltage does not drop at start-up. If the

voltage does drop, ensure the cartridge has a direct

power supply (not from a multi-box or extension cord)

• Failed compressor

• Replace the compressor.

Содержание OD1100N



















































Результаты поиска

Содержание OD1100N

Отзывы:

Бренды по названию

Популярные бренды

Skope OD1100N, Руководство по обслуживанию

Результаты поиска

Содержание OD1100N

Отзывы:

Бренды по названию

Популярные бренды