manualshive.com logo in svg

Skoda Fabia II 2007, Руководство по ремонту

Поделиться
Скачать
Skoda Fabia II 2007 Скачать руководство пользователя страница 75

Complaint

Fault description

Measure

Clutch pedal does not return to ini‐

tial position.

♦ Air in line system.

– Vent air from the line system;

top up with brake fluid.

 

♦ Line system, master or slave

cylinder leaking.

– Replace defective component,

vent air from the line system; top

up with brake fluid.

 

♦ Release bearing is tilted on the

guide bushing, seizured.

– Replace guide bushing and re‐

lease bearing.

 

♦ Membrane spring of the pres‐

sure plate broken.

– Replace pressure plate.

Complaint

Fault description

Measure

Actuating force on the clutch pedal

too high.

♦ Over-centre helper spring de‐

fective.

– Replace over-centre helper

spring.

 

♦ The clutch release force has in‐

creased through the wear of the

clutch lining.

– Inform customer (higher release

force with increased wear).

– Replace the clutch disc if the

distance base of the rivet is be‐

low 0.1 mm.

 

♦ Release bearing is tilted on the

guide bushing, seizured.

– Replace defective components.

 

♦ Pressure plate with wrong

spring identification.

– Assign pressure plate via the ⇒ 

Electronic catalogue of original

parts .

 

♦ Mechanical fault at the pressure

plate or the clutch disc.

– Replace defective components.

 

♦ Clutch disc on the serration

sluggish/jams.

– Check the hub for damage

(burrs), if necessary replace

clutch disc.

– Clean the hub and the drive

shaft serration from corrosion

and residues of lubricant and

grease with grease for plug ser‐

ration of clutch disc -

G 000 100- . Move clutch disc

back and forth, remove excess

grease.

Complaint

Fault description

Measure

Noises when operating the clutch. ♦ Release bearing defective,

guide of clutch release bearing

not in order, contact surface

drained off.

– Always replace noisy release

bearing.

– Replace damaged guide bush‐

ing.

 

♦ Contact surface of the pressure

plate defective (tips of mem‐

brane spring bent, broken). Re‐

lease bearing is off-center.

– Replace pressure plate.

– Check release bearing and

guide bushing, replace if neces‐

sary.

– Check position of clutch release

lever.

– Check dowel sleeves.

Fabia II 2007 ➤ , Fabia II 2009 ➤ , Fabia II 2011 ➤ , Rapid 2011 ➤ , R ...

Gearbox 02T - Edition 05.2014

3. Repairing clutch    

71

Содержание Fabia II 2007






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды