10
Switches off the tool or prevents the tool from being
switched on, when
-
the load is too high
-
the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
-
the lithium-ion battery is nearly empty (to protect
against deep discharge)
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• LED-worklight
-
The LED worklight will automatically turn on with a
slight squeeze on the trigger switch before the tool
starts running, and will turn off 8 to 12 seconds after the
trigger is released.
-
When the tool and/or battery pack becomes
overloaded or too hot, the internal sensors will turn the
tool off. If the tool and/or battery pack are overloaded,
the LED worklight will rapidly flash. Rest the tool for
a while or place the tool and battery pack separately
under air flow to cool.
-
The LED worklight will flash more slowly to indicate that
the battery pack is at low-battery capacity. Recharge
the battery pack.
• Depth adjustment accessory (DEPTH STOP) (not
standard included)
r
APPLICATION ADVICE
• For optimal results on different materials use table
t
as reference for determining the right accessory
(accessories not standard included)
MAINTENANCE
• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots)
! remove battery from tool before cleaning
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
-
in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
-
symbol
5
will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
4
Read the instruction manual before use
5
Do not dispose of electric tools and batteries together
with household waste material
USE
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery
6
• Changing accessories
8
! remove battery from tool
-
remove/mount the required accessory as illustrated
-
ensure that the openings of the accessory engage into
the tabs of the tool head (any snap-in position possible)
-
mount the accessory with the depressed centre
pointing downwards
-
loosen/fasten screw with hex key
-
check the tight seating of the accessory (incorrect
or not securely fastened accessories can come loose
during operation and create a hazard)
• Mounting of sanding sheet
7
-
tap the dust out of the VELCRO material on sanding
pad before mounting the sanding sheet
-
mount VELCRO sanding sheet as illustrated
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total VELCRO surface
covered with sanding paper
• Dust suction
9
! remove battery from tool
-
use vacuum cleaner adaptor only when working with
sanding pad
-
mount vacuum cleaner adaptor as illustrated
-
connect vacuum cleaner
! do not use dust extraction device/vacuum cleaner
when sanding metal
-
clean vacuum cleaner adaptor regularly for optimal dust
pick-up performance
• On/off
-
switch on/off the tool by pushing switch in “I”/”O”
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it from
the workpiece
• Adjusting working speed
q
-
with variable-speed dial the required oscillating
frequency can be adjusted from low (1) to high (6) (also
while tool is running)
-
the optimal working speed depends on the material
and can be determined with practical trials
• Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s)
w
-
keep ventilation slots uncovered
-
do not apply too much pressure on the tool (excessive
pressure will cause excessive heat and may shorten
the service life of the accessory)
• Battery protection
Содержание PWRCORE 20 OS593001E
