background image

-11-

Service

NO USER SERVICE-ABLE
PARTS INSIDE. Preventive

maintenance performed by unauthorized
personnel may result in misplacing of
internal wires and components which
could cause serious hazard.

We recom-

mend that all tool service be performed by a
Skil Factory Service Center or Authorized
Skil Service Station. SERVICEMEN:
Disconnect tool and/or charger from power
source before servicing.

BATTERIES

Be alert for battery packs that are nearing
their end of life.

Battery packs typically last

from 250 to 500 charges.  If you notice
decreased tool performance or significantly
shorter running time between charges then it
is time to replace the battery pack.  Failure
to do so can cause the tool to operate
improperly or damage the charger.

Long term battery storage should be in
the discharged state.

Battery packs last

longer and re-charge better when they are
stored discharged.  Remember to fully re-
charge battery packs before using after
prolonged storage.

TOOL LUBRICATION

Your Skil tool has been properly lubricated
and is ready for use.

D.C. MOTORS

The motor in your tool has been engineered
for many hours of dependable service. To
maintain peak efficiency of the motor, we
recommend it be examined every six
months. Only a genuine Skil replacement
motor specially designed for your tool
should be used.

Cleaning

To avoid accidents, always
disconnect the tool and/or

charger from the power supply before
cleaning.

The tool may be cleaned most

effectively with compressed dry air. 

Always

wear safety goggles when cleaning tools
with compressed air.

Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not attempt to clean by inserting pointed
objects through opening.

Certain cleaning agents
and solvents damage

plastic parts.

Some of these are: gasoline,

carbon tetrachloride, chlorinated cleaning
solvents, ammonia and household detergents
that contain ammonia.

!

WARNING

!

WARNING

Maintenance

!

CAUTION

If an extension cord is
necessary, a cord with

adequate size conductors that is capable
of carrying the current necessary for your
tool must be used.

This will prevent

excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-
wire extension cords that have 3-prong
plugs and receptacles.

NOTE: 

The smaller the gauge number, the heavier

the cord.

RECOMMENDED SIZES OF EXTENSION CORDS

120 VOLT ALTERNATING CURRENT TOOLS

Tool’s 

Ampere 

Rating

Cord Size in A.W.G.

Wire Sizes in mm

2

3-6
6-8

8-10

10-12
12-16

18

16

16

14

.75

.75

1.5

2.5

18

16

14

12

.75

1.0

2.5

4.0

18

16

14

12

.75

1.0

2.5

4.0

16

16

14

12

1.0

2.5

4.0

14

12

25

50

100 150

15

30

60

120

Cord Length in Feet

Cord Length in Meters

!

WARNING

SM 2610995792 10/00   10/9/00 11:32 AM  Page 11

Содержание 120VXT

































Отзывы: