Skeeter FRESHWATER Скачать руководство пользователя страница 73

Страница: 73 / 94

9-4

Table Of Contents

www.SkeeterBoats.com

RUNNING

TRAILERING

A trailer is provided as standard equipment with your Skeeter boat. If you need to obtain another

trailer, choose one that is manufactured to carry a boat of the size and weight of your Skeeter boat.

Check the certification label on the left forward side of the trailer. This label is required to show the

Gross Vehicle Weight Rating (GVWR), which is the load carrying capacity of the trailer plus the

trailer’s weight. Be sure that the total weight of your boat, any cargo, and the trailer weight itself does

not exceed the GVWR.

Hitch

The trailer hitch ball must match the size of the socket on the trailer hitch coupler. Hitches are divided

into classes that specify the gross trailer weight (GTW) and the maximum tongue weight. Always

use a hitch rated for the same or higher class. Use a bolted-on or welded-on hitch; clamp-on bumper

hitches are not recommended. Be sure the trailer hitch’s release handle is latched with the lock pin

installed before towing.

Use safety chains between the towing vehicle and the trailer so the trailer will not detach completely

from the towing vehicle if it accidentally comes loose from the hitch ball. Crisscross the chains under

the trailer tongue so the tongue will not hit the road surface if it falls loose. Rig the chains as tightly as

possible while allowing just enough slack to permit tight turns.

Be sure the tongue weight (vertical weight on the hitch point) is correct. Generally, 5% to 10% of the

combined weight of the boat and trailer should be on the tongue. Too much or too little weight can

cause difficult steering or trailer swaying.

Backing Your Trailer

It takes practice to back a trailer successfully. If you are not familiar backing up with a trailer, practice

first in an open area away from obstacles.

Keep the following points in mind:

• Back slowly. Make steering adjustments in small steps.

• Turn the towing vehicle’s wheels opposite the direction you want the trailer to go.

• After the trailer begins moving, turn the towing vehicle to follow it.

• Have a second person stand by to help direct you with hand signals.

WARNING

Avoid accident and injury from improper trailering.

• The trailer must be matched for the boat’s weight and hull.

• The towing vehicle must have the capacity of pulling the load. Pulling a load that

exceeds the towing capacity may cause loss of control.

• Be sure the boat is secured to the trailer and the trailer is properly hitched to the towing

vehicle before towing.

Содержание FRESHWATER































































































Результаты поиска

Содержание FRESHWATER

Отзывы:

Бренды по названию

Популярные бренды

Skeeter FRESHWATER, Руководство пользователя

Результаты поиска

Содержание FRESHWATER

Отзывы:

Бренды по названию

Популярные бренды