background image

Form 37714 Rev 2002

Page 11 of 13

www.skcinc.com

Replacement Parts

  Use only SKC-approved parts to ensure reliable performance. Failure to do so voids the UL Listing 

for intrinsic safety and any warranty.

  Use of a repaired or rebuilt battery pack voids any warranty and the UL Listing for intrinsic safety.

  Failure to follow warnings, cautions, and notes voids any warranty.

Internal Stack

No.

Description

Cat. No.

1A/1C

Stack screws, pk/12

P51891

2

Inlet/Hose Connect, includes filter and gasket

P20106

2A

Replacement Inlet Filter, pk/10

P40370

3

Pulsation dampener

P2010802

4

Stack plate

N/A

5A/5B

Valve plates (top and bottom)

P213201

6

Diaphragm/Yoke assembly

P2129B

7

Pump body

P22417G

8

Motor/Eccentric

P518803

9

Pump base plate

P20102

Full Stack without Motor

P20102A

Parts not indicated in illustration:

N/A

PC Board

P79592

N/A

Screw and O-ring Set (complete for one pump)

P22402

External Case

No.

Description

Cat. No.

1

Battery Pack, NiMH

P78011AMH

2

Battery Pack Release Arms

N/A

3

Battery Pack Security Screws

N/A

4

Compensation Pot A

N/A

5

Compensation Pot B

N/A

6

Power Plug for Battery Pack, pk/5

P20107

7

Charging Jack (on rear of battery pack)

N/A

8

Impinger Holder Mounting Screws

N/A

9

Inlet (includes filter and gasket)

P20106

10

Control Cover

P20105

11

Flow Adjustment Screw

N/A

12

Power Switch (on/off)

N/A

13

Belt Clip (not shown)

P20104

14

LCD

P72391

15

External Case

P2010003

SKC Limited Warranty and Return Policy

SKC products are subject to the SKC Limited Warranty and Return Policy, which provides SKC’s sole liability and the buyer’s exclusive 
remedy. To view the complete SKC Limited Warranty and Return Policy, go to http://www.skcinc.com/warranty.

1A

2A

8

9

2

3

4

7

5A

5B

6

1B

1C

7

AIRCHEK

®

 52

10

3

  9

14

12

  8

  2

  1

2

4    

5    

6    

11

Bottom of pump 

without battery pack

3

15

13

Содержание 224-52














Отзывы: