24
TN1
Needle Location
U/D/UD
U
//
U: The highest location D: The lowest location
UD: The lowest location, but presser foot rises when
fully pedal.
25
BUZ
Buzzer
ON/OFF
ON
//
When presser foot protection On for 30 seconds (or
set time), the buzzer will beep twice.
26
LE
Overlapping loose
close stitch
200~6000
60
Set stitch to run loose stitches after overlapping and
parameter 14.
27
ABC
Long Suction
ON/OFF
OFF
Enable suction continuously during operation when
set ON.
30
ATF
Start mode selection
ON/OFF
ON
ON: Pedal
OFF: Speed controller
31
INF
Laser light marker
ON/OFF
ON
ON
OFF
32
TFD
Solenoid Valve Check
0~9
0
//
Each code refers to:
1. Presser Foot on (2 seconds).
2. All Off
3. Cut / Suction (50ms)
4. Stretching (2 seconds)
5. Cross Seam
6. Loose Stitch (2 seconds)
7. Ejecting Rod (ref. parameter 82)
8. Aligning
9. Stepping Motor
10. Reserved
11. Reserved
12. Speed Controller Voltage (ref. parameter 82)
33
TIN
Presser foot motion
stimulation
0
、
1
、
2
、
3
0~3
Stimulated mechanism adjustment for seam thickness
34
FT
The initial full output
time of presser
electromagnet
0~990
250
ms
Presser Foot Magnetic Setting.
DO NOT CHANGE
35
FD
Presser Foot Cycle %
10~50%
25
%
The motion cycle of the presser foot electromagnet
36
FPM
Presser Foot
Protection
ON/OFF
ON
//
Protecting functions when the presser foot
electromagnet activates.
37
FP
Presser Foot
Protection Time
1~300
Solenoid:120
E.Mag :30
Second
Set the protection time when the presser foot
electromagnet performs.
38
FMM Presser Foot Mode
ON/OFF
ON
//
When #38 FMM is set ON (presser foot Up), set the
delay time to lower the presser foot.
39
FMS
Presser foot down
delay time.
1~3000
10
ms
40
HT
half pedaling
confirmation time
0~990
100
ms
Set the time of delaying as half pedaling
48
FMD Motor start delay time.
50~500
500
ms
Set the time to start motor after presser foot down.
50 MSW Safety switch
ON/OFF
OFF
//
ON: Enable (When removing the proximity switch,
stop all functions and motors)
OFF: Disable
53
SDA
The stop angle as the
needle descending
0-360
220
Angle DO NOT adjustment
54
SUA
The stop angle as the
needle rising
0-360
30
Angle DO NOT adjustment
55
ER
Error code display
0~9
Set
To save the last error codes up to 10 sets
P9
Содержание ASK-ASM100
