Simu SIMUDRIVE SD510 Скачать руководство пользователя

Страница: 2 / 28

2/28

• Check that a differential switch with a 0.03 threshold is fitted just before the power supply mains.

• Check that earthing is carried out correctly: connect all metal parts for closure (doors, etc.) and all system

components provided with an earth terminal.

• SIMU declines all responsibility with respect to the automation safety and correct operation when other

manufacturer’s components are used.

•  Only use original parts for any maintenance or repair operation.
•  Do not modify the automation components, unless explicitly authorized by SIMU.
•  Instruct the product user about the control systems provided and the manual opening operation in case

of emergency.

• Do not allow people or children to stay in the automation operation area.
• Keep radio control or other control devices out of children’s reach, in order to avoid unintentional automation

activation.

• The user must avoid any attempt to carry out work or repair on the automation system, and always request

the assistance of qualified people.

• Anything which is not expressly provided for in the present instructions is not allowed.

1.4 Safety instructions relating to use and maintenance
WARNING:

Important safety instructions. It is important for the safety of people to follow these instructions.

Save these instructions.

WARNING:

The drive has to be disconnected from its power source during cleaning, maintenance and

when replacing parts.

• This system can be used by children aged from 8 years and above and people with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand the hazards involved. Children

must not play with the appliance. Cleaning and user maintenance should not be made by children without

supervision.

• Do not allow children to play with fixed controls. Keep remote controls away from children.

• Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do

not use if repair or adjustment is necessary.

• Watch the motorised installation while it is moving and keep people away until the motorised installation

is fully extended.

• For drives powered by a very low voltage removable power supply, only the power supply provided with

the drive must be used.

• For drives fitted with a manual release, operating conditions are given in the drive instructions.

• All wiring has do be done with power off.

• PCB protective cover has to be placed before powering on.

Содержание SIMUDRIVE SD510





























Результаты поиска

Содержание SIMUDRIVE SD510

Отзывы:

Похожие инструкции для SIMUDRIVE SD510

Бренды по названию

Популярные бренды

Simu SIMUDRIVE SD510, Руководство пользователя

Результаты поиска

Содержание SIMUDRIVE SD510

Отзывы:

Похожие инструкции для SIMUDRIVE SD510

Бренды по названию

Популярные бренды