background image

EN

1/28

CONTROL BOX 

SIMUDRIVE SD510

5136983C

EN - READ THIS NOTICE 

CAREFULLY BEFORE USE

1.1 Caution – Important safety instructions

For reasons of personal safety, it is important to follow all the instructions, as incorrect installation can lead 

to serious injury. The control box must be installed and adjusted by a professional motorization and building 

automation installer, in compliance with the regulations of the country in which it is going to be used.
The installation and user manual must be given to the end user, explicitly stating that installation, adjustment 

and maintenance of the motorization must be performed by a professional motorization and building 

automation installer.

1.2 Introduction

This control box is designed to control three-phase SIMU motors (<1250W) roll-up or sectional doors in 

commercial or industrial use

.

 It is provided with 3 push buttons (open / close / stop). 

A LED screen allows to check and detect any operating anomalies in the control unit or on the connected 

devices. This product, installed according to these instructions, complies with EN 12453 et EN 12445. 

These instructions are especially designed to ensure the safety of property and people.

1.3 Safety instructions relating to installation

  WARNING! An incorrect installation or improper use of the product can cause damages to people, 

animal or things.

•  Scrap packing materials (plastic, cardboard, polystyrene etc.) according to the provisions set out by 

current standards. Keep nylon or polystyrene bags out of children’s reach.

•  Keep the instructions together with the technical brochure for future reference.

•  This product was exclusively designed and manufactured for the use specified in the present documentation. 

Any other use not specified in the documentation could damage the product and be dangerous.

•  SIMU declines all responsibility for any consequences resulting from improper use of the product, or use 

which is different from that expected and specified in the present documentation.

•  Do not install the product in explosive atmosphere.
•  The installation must comply with the provisions set out by the country in which it is going to be used.
•  Disconnect the electrical power supply before carrying out any work on the installation. Also disconnect 

any buffer batteries, if fitted.

•  The actuating member of a biased-off switch is to be located within direct sight of the driven part but away 

from moving parts. It is to be installed at a minimum height of 1,5 m and not accessible to the public.

•  For door and gate motors fitted with emergency opening/closing controls, switches must not be positioned 

higher than 5 feet above ground level.

•  If the drive is fitted with a manual release, install its actuating member at a height less than 1,8 m.

•  Fit an omnipolar or magneto-thermal switch on the main power supply, having a contact opening distance 

equal to or greater than 3mm.

•  Make sure that there is no crushing between the driven part and the surrounding fixed parts due to the 

opening movement of the driven part.

SAFETY INSTRUCTIONS

1

SIMU S.A.S. au capital de 5 000 000 € - Zone Industrielle Les Giranaux - 70100 ARC-LÈS-GRAY - FRANCE - RCS VESOUL B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090

Содержание SIMUDRIVE SD510





























Отзывы: