SimpliPhi Power BOSS.6 Скачать руководство пользователя страница 3

REV020620

 

 

 

 

 

SimpliPhi Power, Inc.  |  3100 Camino Del Sol  |  Oxnard, CA 93030, USA  |  (805) 640-6700  |  

[email protected]

|  

SimpliPhiPower.com

 

|  1  |          

                                                    

 

 

1.0 – IMPORTANT SAFETY INFORMATION  

 

CAUTION:   DO NOT VOID YOUR WARRANTY- FOLLOW THESE INSTRUCTIONS 
CAREFULLY AND REVIEW WARRANTY DOCUMENT PRIOR TO INSTALLATION 

1.1 - Safety Instructions 

1.

 

Before assembling or using the SimpliPhi Battery Only Storage System for Six Batteries (BOSS.6), read 
all instructions and cautionary markings included in this manual. 

2.

 

Perform all electrical work on the BOSS.6 Enclosure in accordance with local, state and federal 
electrical codes. 

3.

 

The BOSS.6 Enclosure is NEMA 3R-rated for a degree of protection against debris, as well as rain, 
sleet and ice. The Enclosure is NOT watertight and should therefore be protected against excessive 
exposure to liquids. 

4.

 

To reduce the chance of short-circuits and/or electrical shock, always use insulated tools when 
installing or working with this equipment. For the same reason, remove all jewelry such as rings, 
watches, bracelets, etc., and wear insulated rubber electrical gloves when installing or performing 
maintenance on the BOSS.6 Enclosure or the PHI battery modules contained within. 

5.

 

Before assembling or using the BOSS.6, inspect the shipment and the product itself for signs of 
damage. Do not use the BOSS.6 Enclosure if there are indications that it has been damaged during 
shipping or otherwise. Refer to Section 3.1 – Inspection of this Guide for further instruction. 

6.

 

Do not dismantle the BOSS.6 Enclosure; there are no user-serviceable parts contained in this product. 
Doing so will Void the Warranty. 

7.

 

The BOSS.6 Enclosure is designed for the housing and wiring of up to 6 SimpliPhi PHI 3.8, 3.5, or 3.4 
kWh batteries (measuring ~13.5” wide x 15.5” high with terminals x 8.1” deep) or up to 6 SimpliPhi PHI 
2.9, 2.7 or 2.6 kWh batteries (measuring 11.25” W x 12.75” high with terminals x 9.5” deep). Check 
with SimpliPhi Technical Support (

[email protected]

) prior to using the BOSS.6 

Enclosure with any other PHI battery models. 

8.

 

Prior to installing or performing maintenance on the BOSS.6 Enclosure, turn all included PHI Battery 
module built-in circuit breakers’ “ON/OFF” switches to the “OFF” position, and disconnect all wiring 

Содержание BOSS.6


















Отзывы: