Simplicity H924RX Скачать руководство пользователя страница 9

Страница: 9 / 94

1742227

ASSEMBLY

Read and follow the assembly and adjustment
instructions for your snow thrower. All fasteners
are in the parts bag. Do not discard any parts or
material until the unit is assembled.

WARNING: Before doing any
assembly or maintenance to the
snow thrower, pull out the safety

key.

NOTE: In this instruction book, left and right
describe the location of a part from the
operator’s position behind the unit.

NOTE: Torque is measured in foot pounds
(metric N.m). This measurement describes
how tight a nut or bolt must be. The torque is
measured with a torque wrench.

NOTE: Fasteners and loose parts are shown
at full size in Figure 2 on page 85.

NOTE: Illustrations are located on page 2
and on pages 86 through 91.

Tools Required

Knife

Pliers

1/2 inch open end wrenches

9/16 inch open end wrenches

3/4 inch open end wrenches

Measuring tape or ruler

Screwdriver

How To Remove The Snow Thrower
From The Carton

(Figure 3)

The snow thrower is shown in the

shipping position.

2. Remove packing material from wheels,

handle, and auger housing.

3. Locate and remove the parts bag (some

models do not have a parts bag).

4. Cut open the end of the carton next to the

handle.

5. To roll the snowthrower off of the carton, pull

on the handle.

CAUTION: DO NOT back over cables.

6. Remove any packing material that remains

from handle and auger housing.

7. Cut any plastic shipping ties that may secure

the control cables to the LOWER HANDLE.

8. If the control cables have become

disconnected from the control levers, then
attach the cable to the levers (see Owner’s
Manual for illustration of cable and lever).

How To Assemble The Handle And
Crank Assembly

(Figure 4)

Loosen, but do not remove, the

fasteners (1)

in the upper holes of the lower

handle.

2. Remove the fasteners and the

crank

assembly eyebolt (11)

from the lower holes

of the lower handle.

(Figure 1)

Put the

shift lever (6)

into first

forward position.

(Figure 4)

Raise the

upper handle (2)

to the

operating position.

NOTE: Make sure the cables are not
caught between the upper and lower
handle.

5. Install the fasteners and the

crank assembly

eyebolt (11)

that were removed in step 2.

DO NOT tighten until all fasteners are in
place.

(Figure 5)

Attach the

crank rod (15)

to the

universal joint assembly (16)

with the

hair

pin (12).

(Figure 4)

Tighten nut on

eye bolt (11).

Make sure

eye bolt (11)

is properly aligned

and the

crank (18)

can freely rotate.

8. Tighten all handle fasteners.

How To Install The Knob(s)

(Figure 6)

NOTE: If knob(s) are already installed, go to
the next selection.

1. Attach the

knob (3)

onto the

speed shift

lever (2).

On some models, the

knob (3)

is attached. To lock in position, tighten the

hex jam nut (1)

against the bottom of the

knob (3)

2. Make sure the

speed shift lever (2)

functions correctly. Move the

speed shift

lever (2)

through all speeds.

How To Assemble The Chute Deflector

Check The Cables

(Figure 8)

Check the

traction drive cable

(1)

and the

auger drive cable (2)

. If the

bottom of the cables have become
disconnected, reinstall the cables.

(Figure 10)

If the top of the

cables (5)

have

become disconnected from the

drive

levers (6)

, attach the

cables (5)

to the

“Z”

fitting (7)

How To Set The Skid Height

(Figure 1)

The snow thrower is equipped with

height

adjustable skids (7)

mounted on the outside of

the

auger housing (4)

. To adjust the height of

the skids, see “How To Adjust The Height Of
The Skids” in the Maintenance section.

How To Set The Length Of The Cables

The cables were adjusted at the factory and no
adjustments should be necessary. However,
after the handles are put in the operating
position, the cables can be too tight or too loose.
If an adjustment is necessary, see “How To
Check And Adjust The Cables” in the Service
And Adjustment section.

How To Assemble The Drift Cutter
(if equipped)

Drift cutters are used to cut a path through snow
deeper than the auger housing.

(Figure 11)

Loosen the

fasteners (2)

that

secure the

drift cutters (1)

to the auger

housing.

2. Raise the

drift cutters (1)

to the desired

height.

3. Tighten the

fasteners (2).

How To Prepare The Engine

NOTE: The engine was shipped from the
factory filled with oil. Check the level of the
oil. Add oil as needed.

WARNING: Follow the engine
manufacturer’s instructions for the
type of fuel and oil to use. Always

use a safety fuel container. Do not smoke
when adding gasoline to the engine. When
inside an enclosure, do not fill with
gasoline. Before you add fuel, stop the
engine. Let the engine cool for several
minutes.

Check the oil. See the engine manufacturer’s
instructions for the type of fuel and oil to use.
Before you use the unit, read the information on
safety, operation, maintenance, and storage.

Important! Before You Start Operating

Check the fasteners. Make sure all
fasteners are tight.

On electric start models, the unit was
shipped with the starter cord plugged
into the engine. Before operating,
unplug the starter cord from the engine.

OPERATION

NOTE: Illustrations are located on page 2
and on pages 86 through 91.
CAUTION: Use only attachments and
accessories approved by the manufacturer
of the snow thrower (such as tire chains,
electric start kits, etc.).

Know Your Snow Thrower

(Figure 1)

Read this Instruction Book and safety rules
before operation the snow thrower. Compare the
illustration with your snow thrower to familiarize
yourself with the location of various controls and
adjustments.

How To Control The Discharge Of
The Snow

WARNING: Never direct the
discharge of snow toward
bystanders.

WARNING: Always stop the engine
before unclogging the discharge
chute or the auger housing and

before leaving the snow thrower.

(Figure 1)

Turn the

crank assembly (2)

change the discharge direction of the snow.

(Figure 12)

Loosen the

wing knob (1)

the