![background image](http://html1.mh-extra.com/html/silverline/263040/263040_original-instructions-manual_1273384006.webp)
66
GB
o)
Ensure that fasteners are suitable for impact driver use.
Nuts, bolts
and screws that are not suitable for high torque application may
be damaged.
Battery Charger Safety
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger
before attempting to charge the battery.
• DO NOT attempt to use the charger with any batteries other than those
supplied. Keep your battery charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these instructions may
cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer,
the service agent or similarly qualified persons in order to avoid a hazard
WARNING:
DO NOT attempt to recharge non-rechargeable batteries.
Battery Safety
WARNING:
Li-Ion batteries, if incorrectly used, stored or charged are a fire,
burn and explosion hazard.
• Keep the battery out of reach of children
• ONLY charge Li-Ion batteries using the charger provided or designed
specifically for your product
• ONLY use Li-Ion batteries provided with a product or specifically designed
to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure
to follow these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature
(approximately 20˚C)
• Ensure that battery contacts cannot accidentally short in storage. Keep
batteries clean; foreign objects or dirt may cause a short. Keep away
from other metal objects, for example paperclips, coins, keys, nails and
screws
• Under abusive conditions, liquid may be ejected from the battery. This
liquid may cause skin irritation or burns. Avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, seek
medical help
• DO NOT open, disassemble, crush, heat above 60°C or incinerate. Do not
dispose of in fire or similar
Included accessories (not shown):
Blow-moulded case
Intended Use
Battery operated general-purpose impact driver, suitable for light to medium
duty tasks, driving nuts and bolts.
Unpacking Your Tool
• Carefully unpack and inspect your new sander. Familiarise yourself with
all its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
Removing a battery
• To remove the Battery (8) from the impact driver, press the Battery
Release (9), then slide the Battery off the Hand Grip (7)
WARNING:
DO NOT try to remove the Battery without pressing the Battery
Release button. The drill or Battery could be damaged.
Fitting a battery
1. To fit a charged battery, slide it into the Hand Grip (7) of the drill until it
clicks and locks into position
Note:
Make sure the Battery and Impact Driver are lined up correctly. If the
Battery does not slide into the Impact Driver easily, don’t force it. Instead,
slide the Battery out of the Impact Driver again, check the top of Battery
and the Impact Driver battery slot are clean and undamaged and that the
contacts are not bent.
Setting up the battery charger
1. If fitted, remove any battery from the Battery Charger (10)
2. Insert the Mains Plug (11) into a suitable mains socket
Note:
The Green LED (12) on the Battery Charger will illuminate to indicate
that the charger is ready to charge the battery.
WARNING:
ONLY use this charger to charge the supplied battery or
additional purchased batteries that are specifically designed for this tool.
WARNING:
The charger is designed for indoor use only, and MUST NOT be
used in damp or wet conditions.
Charging the battery
WARNING:
Failure to follow the correct procedure when charging batteries
will result in permanent damage.
Note:
Normal charging time is 3 hour for a recently discharged battery.
However, if the Battery (8) has been left in a discharged state for some time,
it may take up to 5 hours to charge.
1. Slide a fully or partially discharged Battery into the Battery Charger
(10)
Note:
Make sure the Battery and Battery Charger are lined up correctly.
If the Battery does not slide into the Battery Charger easily, don’t force
it. Instead, remove the Battery, check the top of Battery and the Battery
Charger slot are clean and undamaged and that the contacts are not bent.
2. Once charging commences, the Green and Red LEDs will illuminate
3. When the Battery is fully charged only the Green LED will be
illuminated
Notes about battery charging:
• The battery should be charged at ambient temperatures between 10 and
40°C (ideally around 20°C)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the charger is disconnected from the mains supply after use,
and is stored correctly
• DO NOT leave batteries on charge for extended periods and NEVER store
batteries on charge
• The Battery Charger monitors battery temperature and voltage while
charging. Remove the Battery once charging has been completed to
maximise charge cycles of the battery and not waste power
• Batteries can become faulty over time, individual cells in the battery
can fail and the battery could short. The charger will not charge faulty
batteries. Use another battery, if possible, to check correct functionality
of the charger and purchase a replacement battery if a faulty battery is
indicated
1
Hex Bit Holder
2
Collar
3
Work Light LEDs
4
Motor Vents
5
Forward/Reverse Switch
6
Trigger Switch
7
Hand Grip
8
Battery
9
Battery Release
10
Battery Charger
11
Mains Plug
12
Green LED
13
Red LED
Product Familiarisation
263302_Z1MANPRO1.indd 6
22/12/2014 09:26
Содержание 263040
Страница 2: ...2 4 9 5 6 7 8 1 2 3 12 13 10 11 2...
Страница 41: ...2 4 8 5 6 7 9 1 2 3 12 13 10 11 2...