15
GB
2.
If desired, first change the pressure level:
Press the pressure button
Pressure Level
|
40
to
switch between
High
|
54
and
Low
|
56
.
3.
The change the cooking time within the adjustable
range:
- Repeatedly press the program button to switch be-
tween the default settings
Less, Normal, More
|
51
.
- You can use the buttons
+
|
33/–
|
46
if necessary to
set the desired time manually.
- By keeping the buttons
+
|
33/–
|
46
pressed, you can
cycle through the values faster.
4.
Briefly press the Start button
Start
|
44
to start the
cooking program.
- The LEDs above the selected program button and
above the Start button
Start
|
44
will be lit continu-
ously.
- The display
|
29
will show
ON
and a running pro-
gress bar
|
55
, indicating that the device is heating up
and building up pressure.
- This may take some time depending on filling volume
and cooking program.
5.
When the temperature and pressure have been
reached, the cooking program starts automatically.
- The display
|
29
counts down the cooking time.
- In order to maintain the temperature, the device auto-
matically switches back and forth between heating
up (progress bar
|
55
running) and heating switched
off (progress bar
|
55
stationary).
6.
The end of the cooking process is signalled by beeps.
The device automatically switches to the warm pro-
gram. The LED of the Cancel button
Keep Warm/
Cancel
|
37
is lit. The display
|
29
counts the warm
time upwards from
00:00.
The pressure is slowly re-
leased.
10.4 Interrupt the cooking process
• To cancel a running program, press the Cancel button
Keep Warm/Cancel
|
37
.
The device is then in standby mode. The display
|
29
will show
OFF
.
10.5 End cooking
1.
End the cooking program or the warm program by
pressing the Cancel button
Keep Warm/Can-
cel
|
37
.
The display
|
29
shows
OFF
. The device is in standby
mode.
2.
Pull the mains plug
|
16
out of the wall socket.
3.
Select a suitable method for reducing the pressure in
the pot and safely opening the lid
|
5
(see “Opening
lid safely (while hot)” on page 12).
4.
Remove the hot pot
|
7
using potholders or oven
gloves.
5.
Allow the device to cool down before you clean it.
10.6 Warm (
Keep Warm/Cancel
)
When a cooking program has ended, the device automat-
ically switches to the warm program
Keep Warm/Can-
cel
|
37
.
You can also start the warm program manually in order to
keep hot food warm in the Multi-Pot.
NOTES:
• Keeping food warm for very long periods changes the
flavour and appearance, vitamins are destroyed, and
the food can go bad.
• Because the warm program works without pressure,
you can open and close the lid
|
5
while the program is
running. You should however be aware of any residual
pressure that may be present after another cooking
program.
• After the yoghurt program (
Yogurt
|
43
), the device
does not automatically switch to the warm program.
1.
Place the hot food into the pot
|
7
.
2.
Wipe down the outside of the pot
|
7
if necessary. It
must be clean and dry.
3.
Place the pot
|
7
into the base unit
|
17
.
4.
Place the lid
|
5
and lock it, such that the arrow mark-
ing
|
6
points to the marking
|
9
. The locking
mechanism will click audibly.
5.
Open the pressure valve
|
1
by pressing down on the
pressure valve button
|
2
until it clicks into place.
6.
Use the mains power cable
|
16
to connect the
port
|
18
on the base unit
|
17
to a properly installed
earthed wall socket that corresponds to the technical
data.
7.
As soon as the device is connected to the power sup-
ply, the display
|
29
will show
OFF.
The device is in
standby mode.
8.
Click the Cancel button
Keep Warm/Cancel
|
37
to start the warm program.
The LED of the Cancel button
Keep Warm/Can-
cel
|
37
is lit. The display
|
29
counts the warm time
upwards from
00:00.
After 12 hours, the warm program ends automatical-
ly.
9.
Click the Cancel button again to end the warm pro-
gram
Keep Warm/Cancel
|
37
.
The LED of the Cancel button
Keep Warm/Can-
cel
|
37
goes out. The display
|
29
will show
OFF
. The
device is in standby mode.
10. Pull the mains plug
|
16
out of the wall socket.
11. Open the lid
|
5
and place it in the drip dry position
(see “Placing lid in drip-dry position” on page 11).
12. Remove the hot pot
|
7
using potholders or oven
gloves.
13. Allow the device to cool down before you clean it.
|
57
This symbol indicates that the device is
heating up and building up pressure.
|
53
This symbol indicates that the set pres-
sure has been reached.
P
Содержание 316620
Страница 2: ...English 2 ...
