background image

Printed in USA 10/13 © 2013

2

36948-EN

3-Product Dairy Dispenser

Model SKBD3LS

P

RINCE

 

C

ASTLE

 

LLC

 

W O R L D W I D E

Limited Warranty

This Silver King branded product is warranted to be free from 
defects in material and/or workmanship for a period of two (2) 
years from the date of original installation, not to exceed 30 
months from date of shipment from our factory. Any part or 
component which proves to be faulty in material and/or 
workmanship (in the opinion of Prince Castle) within the warranty 
period will be replaced or repaired (at the option of Prince Castle) 
without cost to the customer for parts or labor, except as provided 
below. The compressor will carry an additional three (3) years 
parts only warranty. 

This Limited Warranty is subject to the following exceptions/
conditions.

• Use of any non OEM parts voids warranty unless otherwise 

approved by Prince Castle. All work must be performed by an 
authorized Prince Castle Service Agent, except as provided 
herein.

• All covered labor requires preauthorization from the factory 

(Call 1-888-375-2938) and shall be performed during regular 
work hours. Overtime premium will not be covered.

• Travel charges are to be limited to 100 miles (200 Kilometers) 

round trip: 2 hours travel time per one trip repair.

• Adjustments of any kind are not covered under this Limited 

Warranty. 

• Damage caused by carelessness, neglect, and/or abuse (e.g., 

using incorrect voltage, dropping, tampering with or altering 
electrical components, or improper cleaning) is not covered.

• Equipment damaged in shipment or by fire, flood or act of God 

is not covered.

• Damage to coated surfaces is not covered by this Limited 

Warranty.

• Use of refrigerants other than specified on the equipment 

serial plate voids the warranty.

• Labor repair or replacement of the following parts is not 

covered by this Limited Warranty:
– Main Control Board p/n 

36992S;

 Prince Castle will provide 

replacement parts to customer so customer can replace 
such parts if they are defective. Replacement instructions 
are included with part supplied.

– Door Gasket p/n 

36956S,

 Product Containers and Lids (p/n 

37068S,

 

37069S,

 

37070S

 and 

811-006S),

 Drip Tray p/n 

37281S

 and cup guides p/n 

37436S

 are considered wear 

items and are not included under the warranty.

PRINCE CASTLE SHALL NOT BE LIABLE FOR INCIDENTAL 
OR CONSEQUENTIAL DAMAGES, LOSSES, OR EXPENSES. 
PRINCE CASTLE MAKES NO OTHER WARRANTY, EXPRESS 
OR IMPLIED. ALL IMPLIED WARRANTIES OF 
MERCHANTABILITY AND/OR FITNESS FOR ANY 
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND 
EXCLUDED.

Содержание SKBD3LS





















Отзывы: