Silca MARKER 2000 Скачать руководство пользователя страница 13

Страница: 13 / 58

Operating manual - English

MARKER 2000

MACHINE INSTALLATION AND PREPARATION

The marking machine can be installed by the purchaser and does not require any special skills.

The machine is supplied ready for use and does not need to be set up. However, some checks and

preparation for use need to be carried out by the operator.

3.1

Checking for damage

The MARKER 2000 is solid and compact and will not normally damage if transport, unpacking and

installation have been carried out according to the instructions in this manual.

However, it is always advisable to check that the machine has not suffered any damage.

3.2

Environmental conditions

To ensure that the best use is made of the marking machine, certain parameters must be borne in mind:

damp, badly ventilated sites should be avoided.

The ideal conditions for the machine are: temperature between 0 and 40°C, relative humidity approx. 60.

3.3

Positioning

Place the machine on an horizontal

surface, solid enough to take the

weight (20 Kg.).

To facilitate operation the height of

workbench should be approx.100-

120 cm.

It is important to leave sufficient

space, especially behind the

machine (20-30 cm) to ensure

proper ventilation.

Remember to provide space for the

keyboard (fig. 9).

WARNING: ensure that the machine voltage is
the same as that of the mains, which must be
properly

earthed

and

provided

with

differential switch.

Connect the power cable and

keyboard.

Fig. 9

3.4

Description of work station

The machine needs only one operator, who has the following controls at his/her disposal (fig. 9):

- master switch placed on the back of the machine
- clamp for positioning keys to be marked
- keyboard
- display

3.5

Graphics

Fig. 10

WARNING: regulations require that warning label in the language to be used be attached to the machine as shown in
fig. 10.

keyboard

clamp

switch

display

(rear view)

PUNCH

REGULATION

PLATE

CLASS 3B LASER EQUIPMENT

IN ACCORDANCE WITH RULING CEI-76-2

ADHESIVE

LABEL WITH

LASER WARNING

2,5

3,5

1,5

Содержание MARKER 2000



























































Результаты поиска

Содержание MARKER 2000

Отзывы:

Похожие инструкции для MARKER 2000

Бренды по названию

Популярные бренды

Silca MARKER 2000, Руководство по эксплуатации

Результаты поиска

Содержание MARKER 2000

Отзывы:

Похожие инструкции для MARKER 2000

Бренды по названию

Популярные бренды