background image

1 of 12

ÐSIGNET 

5600 Batch Controller

‡ SIGNET 5600 Batch Controller

ENGLISH

CAUTION!

Remove power to unit before wiring input and
output connections.

Follow instructions carefully to avoid personal
injury.

2.   Power Connection

CAUTION!

Never connect 115 VAC or 230 VAC to rear power
terminals.  High voltage AC will damage instrument and
void warranty.

3.  Compatible Sensor Wiring

4.  Batch Contact Wiring

See section 9 for simple and advanced mode configuration
options.

-

+

12-24 V

10 W

-

+

12 - 24 VDC

OR

12 - 24 VAC

5600 
Terminals

External power
supply

Red

Black

Shld.

2000
2507
2536
2540
2550
Vortex*

Red

Black

Shld.

515 
525 
2517

+GF+ SIGNET

 Sensors:

Open Collector 
Sensor

Std. Sensor

Freq. IN

Sen. Pwr.

Freq. IN 

Iso. Gnd

5600 
Terminals

NC

C

NO

NC

C

NO

Batch

Option

flow

AC or DC

power 

valve

5600 
Terminals

Technical Notes:

Maximum alarm contact ratings:  5 A @ 30 VDC, 5 A @ 125
VAC, or 3 A @ 250 VAC

• To reduce the possibility of noise interference, isolate AC power

lines from signal lines.

Technical Notes:

Maximum 4-20 mA loop impedance (sec. 8A) is affected by the
supply voltage.

To reduce the possibility of noise interference, isolate AC
power lines from signal lines.

= Double Insulated

= DC or AC power

Contents

1.

Wiring terminals

2.

Power Connection

3.

Compatible Sensor Wiring

4.

Batch Contact Wiring

5.

Remote Control Wiring

6.

End of Batch/Counter Pulse Output Wiring

7.

Option Contact Wiring Options

Technical Notes:

To reduce the possibility of noise interference, route sensor
cable )away from AC power lines.

• *Vortex sensor or system frequency output

8.

Current Output Wiring Options

9.

5600 Operation Modes

10.

Menu Functions

11.

Parts and Accessories

12.

Specifications

13.

Quick Reference Menu Parameters

14.

Maintenance

15.

Troubleshooting

Total
reset

AUX

output

PLS

output

1

2

Gnd

+

+

-

+

Gnd

Freq. IN

Sen. Pwr.

Freq. IN

Iso. Gnd

Std. Sensor

        

  Patent No.  D376,328

     Flow

Open Collector 
Sensor

12-24 V

10 W

LISTED
77CJ

UL

 1   2   3   4   5   6

 1   2   3   4

 1   2

 1   2

Total
reset

AUX

output

PLS

output

1

2

Gnd

+

+

-

+

Gnd

Freq. IN

Sen. Pwr.

Freq. IN

Iso. Gnd

Std. Sensor

        

  Patent No.  D376,328

     Flow

Open Collector 
Sensor

12-24 V

10 W

LISTED
77CJ

UL

 1   2   3   4   5   6

 1   2   3   4

 1   2

1.

2.

3.

Remove terminal blocks for easy wiring.

1.

Wiring terminals

*3-5600.090-1*

3-5600.090-1 (Rev. D-6/03) English

Содержание GF 5600













Отзывы: