background image

SAFETY INSTRUCTIONS
1.  Depressurize and vent system prior to installation or removal.
2. Con

fi

 rm chemical compatibility before use.

3.  Do not exceed maximum temperature/pressure speci

fi

 cations.

4.  Wear safety goggles or faceshield during installation/service.
5.  Do not alter product construction
6.  If this equipment is used in a manner not speci

fi

 ed by the manufacturer, the protection provided 

by the equipment may be impaired.

7.  This device is not approved for use or installation in hazardous locations.

Signet 2537 Paddlewheel Flowmeter

3-2537.090

3-2537.090 

 

Rev C   06/09    

 English

English

Specifi cations 

General
Wetted Materials

Model Suffi x

Sensor Body

Rotor

Pin

O-ring

-P0, -P1

glass-

fi

 lled PP

PVDF, Black

Titanium

FPM

-T0

PVDF, Natural

PVDF, Natural PVDF, Natural

FPM

Case: 

  PBT, 

yellow

Inside cover: 

 

Valox, black

Wiring ports 

 

½ in. NPT threads; liquid-tight  

 

 

 

 

connector accepts cables 7-10 mm od  

   (0.275-0.394 

in.)

Power requirements

Pulse, Flow Switch
With dry-contact relay:   

24 VDC nominal  

 

 

 

(21.6 VDC min. to 26.4 VDC max.)

   30 

mA 

max 

current

With solid-state relay: 

5 to 24 VDC nominal

 

 

 

(5.0 VDC min to 26.4 VDC max.)

   30 

mA 

max 

current

Digital (S

3

L): 

 

5 VDC nominal

 

 

 

(5.0 VDC min to 6.5 VDC max.)

 

 

 

30 mA max current (1.5 mA nominal)

4-20 mA: 

 

12 VDC to 32 VDC nominal

 

 

 

(10.8 VDC min to 35.2 VDC max.)

 

 

 

 400 mV max ripple voltage

   30 

mA 

max 

current

Reverse Polarity and short circuit protected:  Up to 40V, 1 hour
Over-voltage protection:  +60 VDC, -50 VDC

Paddlewheel sensor performance specifi cations

Pipe Size Range:  

DN15 to DN 200 (½ in. to 8 in.)

Min. Reynolds Number: 

4500

Paddlewheel Frequency:  49 Hz per m/s nominal
 

 

 

(15 Hz per ft/s nominal)

Operating Range:  

0.1 m/s to 6 m/s (0.3 ft/s to 20 ft/s)

Linearity: 

 

±1% of max. range @ 25°C (77°F)

Repeatability         

±0.5% of max. range @ 25°C (77°F)

Electronics performance specifi cations

Input Frequency Range:  1 Hz to 1000 Hz
System Response: 

100 ms update rate nominal

Environmental Requirements 

Enclosure rating:   

NEMA 4X/IP65

Storage Temperature: 

-10°C  to 75°C

Ambient Temperature: 

0°C to 65°C

Relative Humidity: 

0 to 90% RH, non-condensing

Altitude:  

 

2000 m (6562 ft.)

Pollution Degree:  

2

Output specifi cations

Signal Averaging:  

Programmable 0 to 100 seconds

Sensitivity Response: 

Programmable 0 to 9 scale

Pulse divider/Total pulse output

Pulse Divider Setting:  

1.0000 to 99999

 

 

 

Maximum pulse rate: 300 Hz

 

 

 

Maximum pulse width: 50 ms

Flow switch output  

Relay Modes: 

 

Low, High

Time Delay: 

 

0.0 to 6400.0 seconds 

Hysteresis: 

 

Adjustable in Engineering Units

Relay Specifi cations

Mechanical SPDT: 

5A @ 30 VDC, 5A @ 250VAC          

Solid-State Relay: 

100mA @ 40VDC, 70 mA @ 33 VAC

Digital (S

3

L) output

Type: 

 

 

Serial ASCII, TTL level 9600 bps

Maximum cable length: 

See S

3

L speci

fi

 cations

Current output (Passive 4 to 20 mA) 

Loop Accuracy:   

±32 

μ

A (@ 25°C @ 24 VDC)

Loop resolution:   

μ

A

Temp. drift: 

 

±1 

μ

A per °C max.

Power supply rejection:   ±1 uA per V
Maximum cable:    

300 m (1000 ft.)

Max Loop Resistance: 

600

Ω

 @ 24 VDC, 1K

Ω

 @ 32 VDC

Standards & Approvals

• UL
• CE
•      ISO 9001 and ISO 14001

Description

The 2537 Paddlewheel Flowmeter Series offer low 

fl

 ow, low power and high resolution with various output options such as a 

fl

 ow 

switch, pulse divider, Digital (S

3

L), or 4-20 mA.  This unit can be con

fi

 gured on-site directly through the built-in user interface.

• 

The Digital model provides a digital (S

3

L) output for use with the Signet 8900 Multi-Parameter Controller.

• 

The 4-20 mA model provides a blind current loop output.

• 

The Flow Switch Model uses a single relay (mechanical or solid state) for Hi or Lo alarm operation.

• 

The Pulse model uses a single relay (mechanical or solid state) and has two selectable operating modes:

•  The Divider mode scales the paddlewheel frequency down to accommodate low frequency input devices.
•  In Total mode, the Pulse Model becomes a traditional pump pulser, able to output one pulse per a set volume of 

fl

 uid.

A small LCD enables the 2537 to be programmed without any external equipment. During normal operation the display is not visible.

China RoHS (Go to www.gfsignet.com for details)

Содержание 159 001 291













Отзывы: