manualshive.com logo in svg

SignaMax 065-7840, Руководство пользователя


Поделиться
Скачать
background image

Signamax 065-7840 24-Port 10/100/1000BaseT/TX Managed Switch

 

19

 

 

2-1-3-2. Configuring the Management Agent of the 065-7840 Managed Switch 

through the Ethernet Port

  

There are three ways to configure and monitor the switch through the 

switch’s Ethernet port: the CLI, a Web browser, and an SNMP manager. The user 
interface for the last one is NMS dependent and is not covered here. The first two 
types of management interface are discussed in this manual. 

 
 
 
 
 

 

                                            

 
 
 
 
 
 

 

 

• 

Managing the 065-7840 Managed Switch through the Ethernet port 

           

Before you communicate with the switch, you have to finish the            

reconfiguration of the IP address, or you must know the IP address of the switch. 
Then, follow the procedures listed below. 
 

1.  Set up a physical path between the configured switch and a PC via a 

qualified UTP Cat. 5 or better cable with an RJ-45 connector. 

Note: If the PC directly connects to the switch, you have to setup the same 
subnet mask for both of them. But the subnet mask may be different for the 
PC in the remote site. Please refer to Fig. 2-8 about the switch’s default IP 
address information. 

2.  Run the CLI or web browser and follow the menu. Please refer to Chapter 3 

and Chapter 4. 

065-7840 Managed Switch  
Default IP Setting: 
IP = 192.168.1.1 
Subnet Mask = 255.255.255.0 
Default Gateway = 192.168.1.254

Assign a reasonable IP address, 
For example: 
IP = 192.168.1.100 
Subnet Mask = 255.255.255.0 
Default Gateway = 192.168.1.254 

Fig. 2-8

    Ethernet LAN 

Содержание 065-7840





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 065-7840

N-Tron 700 Series User Manual & Installation Manual preview
700 Series
Бренд: N-Tron Страницы: 101
Sagem 2604 Quick Installation Manual preview
2604
Бренд: Sagem Страницы: 19
Wave wifi EC Series Quick Start Manual preview
EC Series
Бренд: Wave wifi Страницы: 2
LaCie Network Space MAX Datasheet preview
Network Space MAX
Бренд: LaCie Страницы: 2
National Instruments NI 9871 Operating Instructions Manual preview
NI 9871
Бренд: National Instruments Страницы: 24
National Instruments NI 9478 Operating Instructions Manual preview
NI 9478
Бренд: National Instruments Страницы: 32
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Бренд: National Instruments Страницы: 8
Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Бренд: Raritan Страницы: 4
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
TRENDnet TE100-S16 - 10/100Mbps Ethernet Switch User Manual preview
TE100-S16 - 10/100Mbps Ethernet Switch
Бренд: TRENDnet Страницы: 15
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Бренд: Grundig Страницы: 24
PairGain PG-Flex FLC-704 Manual preview
PG-Flex FLC-704
Бренд: PairGain Страницы: 20
Raven RFMOW V2 User Manual preview
RFMOW V2
Бренд: Raven Страницы: 33
Xantech RT1610 Installation Instructions Manual preview
RT1610
Бренд: Xantech Страницы: 6
Ricoh Network Scanning Unit A Operating Instructions Manual preview
Network Scanning Unit A
Бренд: Ricoh Страницы: 206
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Бренд: Lindy Страницы: 3
Jensen of Scandinavia Air:Link 29150 Installation Manual preview
Air:Link 29150
Бренд: Jensen of Scandinavia Страницы: 2
Exibel NBG6503 Manual preview
NBG6503
Бренд: Exibel Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды