SignalFire Sentinel-yTherm Series Скачать руководство пользователя страница 9

Страница: 9 / 13

SignalFire Telemetry

Rev 1.6

Status Registers

Register

Address

(Offset)

Description

49987

9986 or 65523 Status (0=no errors, 1=low battery, 2=failed sensor read, 3=low battery and

failed sensor read)

49988

9987 or 65524 Major revision number for the mainboard

49989

9988 or 65525 Minor revision number for the mainboard

49990

9989 or 65526 Major revision number for the radio

49991

9990 or 65527 Minor revision number for the radio

49992

9991 or 65528 High 16 bits of SFTS node address

49993

9992 or 65529 Low 16 bits of SFTS node address (the radio ID)

49994

9993 or 65530 Slave ID readback

49995

9994 or 65531 Received signal strength of last packet from the slave

49996

9995 or 65532 Battery voltage of the Modbus client, in millivolts

49997

9996 or 65533 Minutes until this slave will time out, unless new data is received

49998

9997 or 65534 Number of registers cached for this slave device

49999

9998 or 65535 Remote device type. 0x32 for Sentinel Thermocouple

Содержание Sentinel-yTherm Series














Результаты поиска

Содержание Sentinel-yTherm Series

Отзывы:

Похожие инструкции для Sentinel-yTherm Series

Бренды по названию

Популярные бренды

SignalFire Sentinel-yTherm Series, Инструкция по интерфейсу

Результаты поиска

Содержание Sentinel-yTherm Series

Отзывы:

Похожие инструкции для Sentinel-yTherm Series

Бренды по названию

Популярные бренды