SignalFire Sentinel-yTherm Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 13

background image

12

SignalFire Telemetry

Rev 1.6

Configuration / Debug

WARNING: Only connect to the debug port in a safe area!

Debug and configuration information is available if a connection is made via the debug port on the main
board. A USB converter cable (available from SignalFire) must be used for this interface.

Debug and advanced configuration may be done using the SignalFire Toolkit PC application.

Technical Support and Contact Information

SignalFire Telemetry
140 Locke Dr, Suite B
Marlborough, MA 01752
(978) 212-2868

[email protected]

Revision

Date

Changes/Updates

1.0

10/16/14

Initial release

1.1

4/27/15

Updated to new operation mode for TC Sentinel, added degrees F registers

1.2

5/13/15

Added details for C1D1 certification

1.3

6/5/15

Updated Design

1.5

9/13/17

Added section on encryption, updated warnings

1.6

2/7/19

Updated screenshots
Added Status register
Minor formatting updates

«
...
10
11
12
13
»

Содержание Sentinel-yTherm Series














Отзывы:

Нет отзывов

Похожие инструкции для Sentinel-yTherm Series

Бренд: Varian Страницы: 176

Бренд: Panasonic Страницы: 48

Бренд: Rascal Страницы: 1

Бренд: 2gig Technologies Страницы: 10

Бренд: Xtralis Страницы: 2

Бренд: V-TAC Страницы: 9

Бренд: Ganz Страницы: 2

fontastic Series

Бренд: D-Parts Страницы: 2

Бренд: SecurityMan Страницы: 2

Бренд: DELTA PLUS Страницы: 80

Бренд: Velleman Страницы: 51

Бренд: Datakom Страницы: 13

Бренд: Dante Страницы: 7

Бренд: Gardsman Страницы: 55

DirectIP DC-S6261X

Бренд: Idis Страницы: 20

Бренд: HIKVISION Страницы: 68

Бренд: Ultrak Страницы: 20

Бренд: ST Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды