manualshive.com logo in svg

SIG SUN DANCER 50, Руководство пользователя, Страница: 2 / 22

Поделиться
Скачать
SIG SUN DANCER 50 Скачать руководство пользователя страница 2

Any wrinkles that appear in the covering are easy to remove by
using a hobby-type of heat iron. We suggest covering the iron's
shoe with a thin cotton cloth, such as an old T-shirt to prevent
scratching the film. To shrink AEROKOTE

®

, set the temperature of

your covering iron at 220

O

F - 250

O

F (104

O

C - 121

O

C). Start by using

the heated iron to go over all the seams and color joints, making
sure they are firmly sealed and well adhered.

Then use the 

heated iron to lightly shrink the material - do not press on it. Once
the covering is tight, lightly iron the material back down to the
wood.

You can use a hobby type heat gun to re-shrink the 

covering, but you must be extra careful around the seams.

For part number reference, your Sun Dancer 50 ARF was covered
with SIG AeroKote

®

, using the following colors and part numbers:

SIGRC72ARF(P) - Covered w/ AeroKote

®

#100 White, 

#361 Purple and #360 Violet  or

SIGRC72ARF(Y) - Covered w/ AeroKote

®

#330 Bright Yellow, 

#321 Bright Orange and #311 Bright Red

REQUIRED TOOLS:

For proper assembly, we suggest you have the following tools and
materials available.

A selection of glues:

SIG Thin, Medium and Thick CA 
SIG CA Debonder
SIG Kwik-Set 5-Minute Epoxy
SIG Epoxy (slow cure)

Thread locking compound, such as Loctite

®

Non-Permanent Blue

Screwdriver Assortment
Needle Nose & Flat Nose pliers 
Diagonal Wire Cutters
Small Allen Wrench Assortment
Drill and assorted Drill Bits
Pen Vise for Small Diameter Drill bits
Hobby Knife With Sharp #11 Blades
Paper Towels
Rubbing alcohol for clean up
Scissors
Covering Iron and Trim Seal Tool 
Masking Tape

Dremel

®

Tool With Selection of Sanding and Grinding Bits 

Felt tip pen

KIT CONTENTS:

The following is a complete list of every part included with your Sun
Dancer 50 kit. Use the check-off blocks (

❑

) to inventory your kit

before beginning assembly. Note that the CA type hinges for the
ailerons, rudder, and elevators are in place in each of these parts
but are not yet glued in place. Also note that the bolts and nuts
required to mount your engine to the motor mounts are not 
included in this kit and must be purchased separately.

Note: Do not remove parts from the plastic bags until they are
needed during assembly. All of the required parts, screws, and
bolts, etc. will be included in the bag to assemble a particular 
component of the model.

❑

Bag #1:

Top Wing, fully assembled & covered with AeroKote

®

Holes for mounting cabane struts pre-drilled in hard points
Holes for inter-plane struts (4) pre-drilled in hard points
Ailerons in place with CA hinges - not glued

❑

Bag #2:

Bottom Wing, fully assembled & covered with AeroKote

®

Holes for inter-plane struts (4) pre-drilled in hard points
Wing bolt holes pre-drilled
Wing bolt reinforcement plates pre-drilled and installed
Leading edge wing-mount dowel installed
Aileron servo bays opened up 

w/ plywood servo doublers in place

Aileron servo installation strings in place
Ailerons in place with CA hinges - not glued
Aileron servo lead holes pre-drilled at center section

❑

Bag #3:

Vertical Fin, covered with AeroKote

®

Covering removed from bottom for attaching to fuselage
Pre-slotted for the top 2 CA hinges

❑

Bag #4:

Rudder, covered with AeroKote

®

Pre-slotted for 3 CA hinges
CA hinges in place - not glued

❑

Bag #5:

Horizontal Stabilizer & Elevator covered with AeroKote

®

Pre-slotted to accept vertical fin
Covering removed from bottom of stabilizer for gluing 

to fuselage

Elevators attached to stabilizer with 4 CA hinges 

- not glued

❑

Bag #6:

Fuselage, covered with AeroKote

®

Windshield installed with 3 M2 X 8mm PWA screws
3mm Motor Mount Blind Nuts installed with fuel tank 

opening in firewall

Fuel Tank Hatch installed w/ 4 M2 X 6mm PWA screws
Fuselage pre-slotted for cabane struts
Fuselage pre-drilled for cabane strut bolts 

w/ 3mm blind nuts installed

Fuselage pre-drilled for landing gear attachment 

w/ 4mm blind nuts installed

Hard point for tail wheel mounting
Fuselage slotted at tailpost for bottom rudder CA hinge
Bottom Wing Bolt Tray installed 

w/ two 1/4-20 blind nuts installed

Firewall fuel-proofed

2

Modeler's Tip: One of the most common problems associated
with shrinking any covering film is controlling the heat around
the seams.

Heat applied close to or directly onto seams 

re-heats the covering adhesive and the seams will often "crawl".
This is easy to control. Just tear a few paper towels into strips
and soak them in cool tap water. Lay the wet strips over the
covering seam and use a heat gun or iron as you normally
would. The wet strips keep the seam cool while the covering
immediately next to it shrinks. This tip works great with any 
iron-on covering.

Содержание SUN DANCER 50























Отзывы:

Нет отзывов