SIG Sealane Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 26

SIG Sealane Скачать руководство пользователя страница 2

.

Engine Selection

Engine choices for the SEALANE are many. The SEALANE has been designed to produce excellent performance when using
the recommended engine sizes. Do not use an engine larger than recommended.

2-stroke engines are a perfect choice to power your SEALANE. Any plain-bearing or
bearing equipped .40 to .45 sport engine would be a good choice. For example, a
great choice would be the Irvine .40 engine. Like all Irvine engines, the .40 is
powerful, reliable, and quiet. Whatever engine you choose, take the time to carefully
break it in according to the manufacturer’s instructions. A good running, reliable
engine is a minimum requirement for the enjoyment of this or any R/C model aircraft.

The SEALANE can also use a variety of 4-stroke engines. Any 4-stroke engine in
the .40 - .50 displacement range should provide plenty of power. An important thing to
remember is that typical 4-stroke engines have their throttle arms usually located
differently than throttle arms on 2-stroke engines. If you want to power this model with
a 4-stroke engine, you will likely have to install a new, relocated throttle cable tube. While this is not difficult, it is something to
consider when choosing an engine.

Covering Material And Waterproofing

Your SEALANE has been designed to be completely covered with any of the popular plastic iron on covering materials on the
market. These covering materials are waterproof and by carefully overlapping the seams approximately 3/32", your SEALANE
will be almost waterproof.

The only place on the model where water can enter the fuselage is at the joint where the wing attaches. Our prototype models
were made with relatively tight fitting wings, with no additional sealing, and very little water was able to enter the fuselage.

Required Tools

A selection of glues:

A selection of hand tools, such as:

Sig Thin CA

Sig Medium CA

Sig thin CA applicator tips

Sig Kwik-Shot Accelerator

Sig Epoxy Glue (15 Minute
Working Time)

Regular size and miniature
screwdrivers

Regular size and miniature
pliers

Tweezers or small hemostats

Hobby knife with several new
#11 blades

Sandpaper-assorted grits

Sig Modelers “T” pins

Drill Motor

1/16” Drill Bit

3/16” Drill Bit

1/4” Drill Bit

Covering Iron

Wax Paper

Fuel Proof Paint

Small Paint Brush

Razor saw or
Hacksaw blade

Pencil

Small 90° Square

Masking tape and
Rubber bands

COMPLETE KIT PARTS LIST

Laser Cut Parts

There are 13 Laser Cut Sheets included in this kit. Use the illustrations on the following pages to identify these parts.

Wooden Parts

Qty Assembly Name

Size & Material

Qty Assembly Name

Size & Material

1

Fuselage

Fuse Nose Top
Stringer

1/4”x1/4”x13” Balsa Stick

2

Fuselage

Fuse Nose Top Sheet

3/32”x3”x13” Balsa Sheet

28

Fuselage

Fuse Bottom Sheet

3/32”x3”x3” Balsa Sheet

1

Fuselage

Windshield Top Block

1”x1”x4-1/2” Balsa Block

1

Fuselage

Nose Block

4”x2-3/4”x3” Balsa Block

1

Fuselage

Windshield Top Sheet

3/32”x1-3/4”x4-1/2” Balsa
Sheet

1

Fuselage

Fuse Aft Bottom
Block

1/4”x2-1/2”x6” Balsa Sheet

2

Fuselage

Bolt Block & Firewall
Reinf

1/4”x1/4”x7” Balsa Triangle

2

Fuselage

Servo Tray Support 1/4”x1/4”x5-1/4” Balsa Stick

1

Fuselage

Switch Wire Guide

1/4”x1/4”x1” Spruce Stick

4

Wing

Main Wing Spars

1/4”x1/4”x30” Spruce

2

Wing

Trailing Edges

1/4”x1/4”x30” Balsa Stick

4

Wing

Trailing Edge Sheet 3/32”x1”x30” Balsa Sheet

2

Wing

Leading Edges

3/8”x3/8”x27” Balsa Stick

2

Wing

Leading Edge Sheet 3/32”x3”x30” Balsa Sheet

2

Wing

Leading Edge Sheet

3/32”x3 1/8”x30” Balsa Sheet

8

Wing

Center Section
Sheet

3/32”x3”x12” Balsa Sheet

4

Wing

Cap Strip Material

3/32”x1/4”x36” Balsa Stick

2

Wing

Wing Tip

1-1/2”x1-1/2”x11-1/2” Balsa
Triangle

4

Wing

Tip Float Anchor

1/2”x15/16”x1.15” Hardwood

«
1
2
3
4
...
»

Содержание Sealane



























Отзывы:

Нет отзывов