SIG RASCAL 110 EG ARF, Инструкция по сборке, Страница: 4 / 24

radio into fail-safe and cause a crash. (Be sure to check your
receiver and servo specifications for min and max allowed
voltage when selecting a receiver battery pack - especially
if going above 6.0 volts with a lipo pack - you may need
high voltage servos to use lipo.)
We also recommend that your receiver battery pack have a
1500-2000 mAh capacity. Be sure you have a charger capable
of properly charging these larger battery packs.
No radio equipment is supplied in this kit. Heavy-duty servos,
extension cords of various lengths, and Y-harness cords are all
available separately from your radio manufacturer. Check their
website, or see your local hobby shop for more information.
REQUIRED TOOLS
For proper assembly, we suggest you have the following tools
and materials available:
A selection of glues - SIG Thin, Medium, & Thick CA Glue
CA Accelerator, CA Debonder
SIG Kwik-Set 5-Minute Epoxy
Screwdriver Assortment
Pliers - Needle Nose & Flat Nose
Diagonal Wire Cutters
Small Allen Wrench Assortment
Pin Vise for Small Dia. Drill Bits
Hobby Knife with Sharp #11 Blades
Small Power Drill With Selection of Bits
Dremel
® Tool With Selection of Sanding & Grinding Bits
Scissors
Sandpaper
Heat Iron & Trim Seal Tool
Masking Tape
Paper Towels
Alcohol and/or Acetone For Epoxy Clean-up
Threadlock Liquid (such as Loctite
® Non-Permanent)
COMPLETE KIT PARTS LIST
The following is a complete list of all parts contained in this kit.
Before beginning assembly, we suggest that you take the time
to inventory the parts in your kit. Use the check-off boxes
❑
provided in front of each part description.
❑ (1) Fuselage
❑ (1) Right Wing w/ Aileron & Flap, hinges not glued
❑ (1) Left Wing w/ Aileron & Flap, hinges not glued
❑ (1) Stabilizer & Elevator, hinges not glued
❑ (1) Fin & Rudder, hinges not glued
❑ (1) Fiberglass Cowling
❑
(1) Right Plastic Side Window
❑
(1) Left Plastic Side Window
❑
(1) Plastic Windshield
❑
(1) Aluminum Main Landing Gear
❑ (1) Right Fiberglass Wheel Pant
❑ (1) Left Fiberglass Wheel Pant
❑ (1) Aluminum Tube Wing Joiner
❑ (1) Balsa Triangle Stock
❑
(1) Right Wing Strut
❑
(1) Left Wing Strut
❑
(1) Plywood Electric Motor Mount
❑
(1) Plywood Battery Tray
❑ (2) 3-3/8" long Wire Pushrod, threaded both ends,
w/ Hex Nuts; for flaps
❑ (2) 4" long Wire Pushrod, threaded both ends,
w/ Hex Nuts; for ailerons
❑ (1) 5" long Wire Pushrod, threaded both ends,
w/ Hex Nuts; for elevator
❑ (1) 17-3/4" long Wire Pushrod, threaded one end,
w/ Hex Nut; for throttle
❑ (1) 15" long Nylon Pushrod Tube, for throttle pushrod sleeve
❑
(2) Velcro
®
Straps
❑
(2) 4" dia. Main Wheels
❑
(2) Plastic-coated Steel Pull-Pull Cables
❑
(4) Metal Pull-Pull Swage Tubes
❑ (8) Magnets (removable side windows for electric power)
❑ (1) Tailwheel Assembly, with Steering Arm
❑ (3) M3 x 20mm Socket-Head Bolts, for mounting tailwheel
❑ (1) Metal 3-Arm Rudder Steering Horn
❑ (2) M2.8 x 15mm Screws; for mounting rudder steering horn
❑ (2) Coil Steering Springs
❑ (2) M6.5 x 45 mm Nylon Wing Bolts
❑ (1) M4 x 20mm Nylon Bolt; for battery/tank tray
❑
(4) Brass Pull-Pull Fittings; for rudder
❑
(4) M2.7 Hex Nuts; for pull-pull fittings
❑
(14) M2.7 Metal Clevis; for ail(4), flaps(4), rud(4), ele(2)
❑
(1) M1.7 Metal Clevis; for throttle pushrod
❑ (1) Pushrod Connector w/ Set Screw; for throttle pushrod
❑ (15) Short pieces of Fuel Tubing; for clevis keepers
❑ (5) Nylon Control Horns w/ Clamp; for ail(2), flaps(2), ele(1)
❑ (2) Nylon Control Horns w/o Clamp; for pull-pull rudder
❑ (12) M2 x 30mm Bolts; for control horns, ail(6), flaps(6)
❑ (6) M2 x 20mm Bolts; for control horns, elev(3), rudder(3)
❑ (18) M2 Hex Nuts; for control horns
❑ (23) M2.3 x 7mm Screws; for windshield & ail./flap hatches
❑ (6) M3 x 10mm Sheet Metal Screws, for cowling
❑
(4) M3 x 12mm Socket-Head Bolts, for wheel pants
❑
(12) M4 x 20mm Socket-Head Bolts, for landing gear(4),
electric motor(4), wing struts(4)
❑
(4) M4 x 25mm Socket-Head Bolts; for electric motor mount
❑ (4) M4 Flat Washers; for electric motor mount
❑ (8) M4 Lock Washers, for landing gear(4), electric motor(4)
❑ (8) M4 Blind Nuts; for electric motor & mount
❑ (2) 4mm dia. Axles
❑ (2) Large Hex Nuts; for axles
❑ (4) 4mm ID Wheels Collars w/ Set Screws; for axles
Your RASCAL 110 is covered with Oracover ® , a premium
quality covering made in Germany, and sold in the U.S. by
Hanger-9 as Ultracote
® .
Colors
Oracover ® #10 White (Ultracote ® #HANU870)
and
Oracover ® #29 Transparent Red (Ultracote ® #HANU950)
or
Oracover
®
#59 Transparent Blue (Ultracote
®
#HANU954)
4
COVERING MATERIAL