.
The laser cut balsa and plywood parts can be identified using the "KEY TO LASER CUT PARTS". Mark the identification
numbers on the corresponding parts before removing them from the laser cut sheets. Leave all the laser cut parts in the sheets
until needed in construction. Then remove the pieces from the sheets carefully. Use a sharp #11 hobby knife to cut through any
"tabs" that are holding the parts in the sheets. Lightly sand off any remainder of the tabs, flush with the actual edge of the part.
All of the other parts can be identified by the "KIT INVENTORY LIST" that follows. Sort the different sizes of sticks and sheets
into individual piles to avoid confusion during building.
COMPLETE KIT PARTS LIST
Laser Cut Balsa Wood Parts
2 1/16"x3"x36" Sheet No.1: wing ribs W-2,
W-3, W-4, W-4A
1 3/32"x3"x36" Sheet No.2: Fuselage Top
1 3/32"x3"x36" Sheet
No.3: fuselage parts
FBT-2, FD-1
1 3/32"x3"x36" Sheet
No.4: W-1 wing ribs,
Spar Webs
2 3/32"x4"x36" Sheet No.5: Fuselage Sides
1 3/16"x3"x36" Sheet No.6: tail parts Tail
Parts; S-1, S-2, S-3, S-4, S-5, S-6, S-7, S-8,
S-9, E-1, E-2, E-3, E-4, E-5, E-6, E-7, R-1,
R-2, R-3, R-4, R-5, R-6, R-7, R-8, F-1, F-2,
F-3, F-4, F-5, F-6, F-7
1 3/16"x3"x36" Sheet
No.7: W-1A,
Ailerons, Wingtips
Laser Cut Plywood Parts
1 1/8"x6"x24" Sheet No.8: APG, F-1A, F-1B,
F-2, F-2B, F-3, F-4, F-4T, F-5, F-5T, F-6, F-
6T, FBT-1, BT, DB, FHR, HT-1, HT-2, LG-1,
LG-2, P-1, P-2, SM-1 (4), T-1, T-2, TWM,
WBP
2 1/4" Motor Spacers
Balsa Wood Sticks
3 3/32"x3/16"x36" Stringers
1 1/16"x1/4"x18" Capstrips
8 1/8"x1/8"x24" Sub
Spars
4 1/8"x3/8"x36" Main
Spars, Main Spar
Doublers, Servo Bay
4 1/4"x1/4"x24" Leading & Trailing Edges
Balsa Wood Sheets
2 1/16"x1-1/4"x24" Trailing Edge Top Sheet 2 1/16"x1-1/2"x24" Trailing Edge Bottom
Sheet
2 1/16"x2"x24" Wing
Center Section
Sheeting
1 3/32"x3"x13" Fuselage
Top Sheeting
Hardwood
2 1/4"x1/4"x2-9/16" Servo Mount Rails
1 1/4" dia.x1-1/2" Birch Dowel
Music Wire
1 1/16"x4-3/8" formed Tailwheel Wire
1 1/16"x4-1/4" formed Elevator Joiner
2 1/32"x24" Elevator
& Rudder Pushrods
Plastic Parts
1 Molded Plastic Canopy
1 Molded Plastic Cowling
Hardware
2 2-56x10" Threaded Rods; for aileron
pushrods
1 3/4" dia. Tailwheel
4 Nylon RC Links; for
rud(1), ail(2), ele(1)
2 Right Nylon Control
Horns; for ele(1), left
ail(1)
2 Left Nylon Control Horns; for rud(1), right
ail(1)
1 Nylon Landing Gear Clip
1 Nylon Tailwheel
Bracket
8 #2x3/8" Sheet Metal
Screws; for cowling,
hatch, tailwheel
bracket
8 #2x1/2” Sheet Metal Screws; for control
horns
1 2-56x3/8" Bolt; for tailwheel
1 2-56 Hex Nut; for
tailwheel
2 4-40 Blind Nuts; for
main landing gear
2 4-40x3/8" Bolts; for main landing gear
2 6-32x1-1/2" Bolts; for axles
2 6-32 Lock Nuts; for
axles
4 6-32 Hex Nuts; for
axles
14 Hinges; for ail(6), ele(4), rud(3), tailwheel
(1)
1 10-32x1" Nylon Wing Bolt
1 10-32 Blind Nut; for
wing hold down
2 Threaded Couplers; for
elevator & rudder
pushrods
1 1/16" id Wheel Collar & Set Screw; for
tailwheel
1 Hex Key Wrench
Misc
1 formed Aluminum Landing Gear
2 .130 odx19 Nylon Pushrod Tubes
1 Decal Sheet
SIGDKM106A
1 Decal Sheet
SIGDKM106B
Содержание Four-Star 20EP
Страница 5: ... ...
