manualshive.com logo in svg

Sierra Flame Lynwood W76, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sierra Flame Lynwood W76 Скачать руководство пользователя страница 12

Page 12

Multi-purpose cap

Storm collar

Flashing

Chimney 

section

Connector 

pipe

Attic insulation 

shield

Firestop 

assembly

Ceiling 

support

Factory Chimney Top vent installation

Required installation components:

 

Chimney cap 

 

Insulated chimney 

 

Storm collar 

 

Roof flashing 

 

Ceiling support box or joist shield/fire stop spacer 

 

Chimney connector pipe 

 

Chimney connector adapter 

Chimney  connector

The chimney connector is a single or walled pipe used to con-

nect the stove to the chimney.  For use with the SIERRA FLAME 

wood-burning stoves the chimney connector MUST be 6” in 

diameter, with a minimum thickness of 24 gauge black steel or 26 

gauge blued steel

Aluminum and galvanized steel pipe is not acceptable for use 

with the SIERRA FLAME wood-burning stove.  These materials 

cannot withstand the extreme temperatures of a wood fire and 

can give off toxic fumes when heated.

DO NOT USE THE CONNECTOR PIPE AS A CHIMNEY

Each chimney connector or stove pipe section must be connected to the 

stove flue collar and to each other with the male (crimped) end toward the 

stove. Each adjacent piece of connector must be fastened with 2   screws. 

This prevents any condensed or liquid creosote from running down the out-

side of the pipe or the stove top. All joints, including the flue collar connection 

must be secured with three sheet metal screws to ensure that the sections 

do not separate.  For the best performance the chimney connector should be 

as short and direct as possible, with no more than one 90 degree elbow.  The 

maximum horizontal run is 36” and a recommended total length of connector 

pipe should not exceed 10 feet.  Always slope horizontal runs upward ¼” per 

foot toward the chimney. No part of the chimney connector may pass through 

an attic or roof space, closet or other concealed-space, or through a floor ceiling.  All sections of 

the chimney connectors must be accessible for cleaning.  Where passage through a wall or parti-

tion of combustible construction is desired, the installation must conform with NFPA 211 or CAN/

CSA-B365.

Содержание Lynwood W76
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды