background image

Published by 
Siemens 2021

Siemens Industry, Inc.

 

3617 Parkway Lane 
Peachtree Corners, GA 30092 
 
Siemens Technical Support: 1-800-333-7421 
[email protected]
 
Printed in USA-CP                                                                                                                           
Order No. RPIM-TPS41-0321 
All Rights Reserved 
© 2021, Siemens Industry, Inc.                                                                                   
usa.siemens.com/spd

The technical data presented in this document is based on an actual case 
or on as-designed parameters, and therefore should not be relied upon for 
any specific application and does not constitute a performance guarantee 
for any projects. Actual results are dependent on variable conditions. 
Accordingly, Siemens does not make representations, warranties, or 
assurances as to the accuracy, currency or completeness of the content 
contained herein. If requested, we will provide specific technical data or 
specifications with respect to any customer’s particular applications. Our 
company is constantly involved in engineering and development. For that 
reason, we reserve the right to modify, at any time, the technology and 
product specifications contained herein.

Содержание TPS4-01

















Отзывы: