Siemens Synco living Скачать руководство пользователя страница 57

Страница: 57 / 100

57 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Actual value of the DHW temperature

The actual value of the DHW temperature can be displayed:

Main menu > DHW > DHW state > Act val DHW temp:

DHW temperature setpoint

The current DHW temperature setpoint can be queried:

Main menu > DHW > DHW state > DHW temp setpoint:

Operating state of charging pump and electric
immersion heater

The current operating state of the charging pump and the electric immersion
heater can be displayed:

Main menu > DHW > DHW state > Charging pump:

Main menu > DHW > DHW state > El immersion heater:

Plant operation

The current operating state of DHW heating (Off / Ready / Charging) can be
displayed:

Main menu > DHW > DHW state > Plant operation:

Reason for DHW plant operation

The reason for the current DHW plant operation can be displayed (commis-
sioning / frost / legionella function / time switch):

Main menu > DHW > DHW state > Cause:

Limitation of charging time

This display shows whether limitation of the charging time is currently inactive
or active. The maximum permissible charging time was preset when the plant
was commissioned.

Main menu > DHW > DHW state > Charging time limit:

Содержание Synco living





































































































Результаты поиска

Содержание Synco living

Отзывы:

Похожие инструкции для Synco living

Бренды по названию

Популярные бренды

Siemens Synco living, Руководство по эксплуатации

Результаты поиска

Содержание Synco living

Отзывы:

Похожие инструкции для Synco living

Бренды по названию

Популярные бренды