Siemens Synco living Скачать руководство пользователя страница 24

Страница: 24 / 100

24 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Menu level

Press the

Menu / ok

button to go from the quiescent picture or the info page

to the menu level (main menu). Press the

Esc

button to return to the quies-

cent picture.

Main menu

Apartment…

Rooms…

Ventilation…

DHW…

The menu header “Main menu” and
associated symbol are display fol-
lowed by a list of available menus.

Setting principle

General rules

Values are always readjusted in an additional window on the display (edit pop-
up). The range of action (cursor) always appears inverse.

Readjustments are made in individual steps with the

Arrow

buttons (up /

down). Longer pushes on the buttons speed up the process. Confirm the
setting by pressing the

Menu / ok

button. To cancel the process or to navigate

back to the next higher menu level, press the

Esc

button.

The following examples illustrate the different setting choices.

Setting a numerical value

Comfort

With numerical values, the setting
range is shown on the left (upper and
lower limit). The current setting value
appears inverted on the right.

Selecting the selection list

Preselection

Auto

Comfort

Precomfort

For a number of functions, a selection
list is available. The selection made is
identified by a tick ”

“. Only one

element of the list can be activated at
a time.

Содержание Synco living





































































































Результаты поиска

Содержание Synco living

Отзывы:

Похожие инструкции для Synco living

Бренды по названию

Популярные бренды

Siemens Synco living, Руководство по эксплуатации

Результаты поиска

Содержание Synco living

Отзывы:

Похожие инструкции для Synco living

Бренды по названию

Популярные бренды