Siemens Synco living Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 100

background image

56 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Operating mode via contact

Specify the type of DHW operating mode the controller is to change over to
when an external operating mode contact is connected (e.g. teleswitch for
remote operation by phone).

Operating mode changeover via external contact overrides all other operating
mode settings.

The input function “operating mode contact” must be configured during
commissioning.
The same operating mode contact is used for heating / cooling, venti-
lation and DHW.

Main menu > DHW > Operating mode > Optg mode contact:

Factory setting

---

Your Setting

--- (no influence, by time switch program)

Normal

Reduced

Protection

DHW temperature setpoint

If the DHW temperature is too high or too low, you can change the setpoint:

Main menu > DHW > Setpoints > Normal setpoint:

Main menu > DHW > Setpoints > Reduced setp:

Normal setpoint

Reduced setpoint

Factory setting

55 °C

40 °C

Your setting

DHW time switch

In DHW operating mode “Auto“, the central apartment unit controls DHW
charging in accordance with the DHW time program.

Main menu > DHW > Time switch > Weekday X:

You can set up to 6 switching points for each weekday plus one special day.
You can also define the DHW temperature setpoint (Normal or Reduced) to be
used at each switching point.

The switching points can be set, deleted or copied to some other weekday.
The settings are made analogously to the room time switch settings (refer to
page 37).

The central apartment unit is supplied with the following factory set-
tings for all weekdays: 05:00 for changeover to the Normal setpoint,
22:00 for changeover to the Reduced setpoint.

«
...
54
55
56
57
58
...
»

Содержание Synco living





































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco living

Бренд: C&K systems Страницы: 2

Бренд: E-fly Страницы: 16

ElectraElite IPK

Бренд: NEC Страницы: 20

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Bartec Страницы: 26

Бренд: VCON Страницы: 48

Бренд: V2 Страницы: 48

Бренд: janitza Страницы: 58

Бренд: Sanhua Страницы: 3

Бренд: QED Страницы: 26

Бренд: Universal Remote Страницы: 20

Бренд: Klimaire Страницы: 5

UNDER CONTROL CP-30A PILOT

Бренд: G-Force Страницы: 2

Бренд: Fluidmaster Страницы: 2

Бренд: M-system Страницы: 9

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Ezi-IO EtherCAT DA

Бренд: Fastech Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды