Siemens SIWAREX WL280 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 58

Siemens SIWAREX WL280 Скачать руководство пользователя страница 32

Mounting

5.2 Installing the compact installation unit

RN-S SA

32

Operating Instructions, 09/2016, A5E32605810A-03

5.

Remove the pressure piece with the flat seal from accessory kit 1.

6.

Place the pressure piece with the flat seal onto the pendulum support.

Installing the load cell

1.

Insert the load cell

①

complete with pendulum support and pressure piece into the

compact installation unit.
Slide the load cell until it rests against the two pins

②

.

Figure 5-4

Inserting the load cell

2.

Push the pressure piece against the two pins.

3.

Secure the load cells with the previously removed clamping washer

③

.

Figure 5-5

Tightening the load cell

4.

Secure the pressure piece with the previously removed clamping washer

④

. Make sure

before securing that the pressure piece is resting on the top plate.

As long as you do not loosen the hexagon nuts on the top plate, the compact installation unit

with the load cell is installed in a stable state with the set added excess length. The load cell

is relieved and protected against an overload during the assembly.
The top plate is ideally centered above the base plate.

«
...
30
31
32
33
34
...
»

Содержание SIWAREX WL280



























































Отзывы:

Нет отзывов