Siemens SITRANS RD300 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 110

Siemens SITRANS RD300 Скачать руководство пользователя страница 37

SITRANS RD300

A5E31917845

SITRANS RD300 – OPERATING INSTRUCTIONS

Page 31

Programming the Meter (

prog

)

It is

very important

to read the following information, before proceeding

to program the meter:



The meter is factory calibrated prior to shipment to read in
milliamps and volts depending on the input selection. The
calibration equipment is certified to NIST standards.



Use the

Scale

menu to scale the process input (e.g. 4-20 mA). A

calibrated signal source is not needed to scale the meter.



Use the

Calibrate

menu to apply a signal from a calibrator or a

flowmeter.



The RD300 is a single input meter with dual-scale capability.

The

Program

menu contains the

Scale

and the

Calibrate

menus.

Note: The

Scale

and

Calibrate

functions are exclusive of each other.

The meter uses the last function programmed. Only one of these
methods can be employed at a time. The Scale and Calibrate functions
can use up to 32 points (default is 2). The number of points should be set
in the Advanced menu under the Multi-Point Linearization

(Linear)

menu

selection prior to scaling and calibration of the meter, see page 80 for
details.

If the dual-scale level feature is selected in the

Setup

menu, the

Scale 1

and

Scale 2

menus are enabled for PV1 & PV2 respectively.

The process input may be calibrated or scaled to any display value
within the range of the meter.

Program Menu for Single Scale Process

Program Menu for Dual-Scale Level Applications

Additional parameters, not needed for most applications, are
programmed in the

Advanced

Features

menu; see

Advanced Features

Menu

, page 74.

«
...
35
36
37
38
39
...
»

Содержание SITRANS RD300















































































































Отзывы:

Нет отзывов