Siemens SITRANS RD300 Скачать руководство пользователя страница 108

Страница: 108 / 110

SIT SITRANS RD300RANS RD300

Page 102

SITRANS RD300 – OPERATING INSTRUCTIONS

A5E31917845

Electromagnetic Compatibility

EMISSIONS

EN 55022:2010
Class A ITE emissions requirements

Radiated
Emissions

Class A

AC Mains
Conducted
Emissions

Class A

IMMUNITY

EN 61326-1:2013
Measurement, control, and laboratory equipment
EN 61000-6-2:2005
EMC heavy industrial generic immunity standard

RFI - Amplitude
Modulated

80 -1000 MHz 10 V/m 80% AM (1 kHz)
1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)
2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)

Electrical Fast
Transients

±2kV AC mains, ±1kV other

Electrostatic
Discharge

±4kV contact, ±8kV air

RFI - Conducted

10V, 0.15-80 MHz, 1kHz 80% AM

AC Surge

±2kV Common, ±1kV Differential

Surge

1KV (CM)

Power-Frequency
Magnetic Field

30 A/m 70%V for 0.5 period

Voltage Dips

40%V for 5 & 50 periods
70%V for 25 periods

Voltage
Interruptions

<5%V for 250 periods

Note:
Testing was conducted on RD300 meters installed through the
covers of grounded metal enclosures with cable shields
grounded at the point of entry representing installations
designed to optimize EMC performance.

Declaration of Conformity available at www.siemens.com

Содержание SITRANS RD300















































































































Результаты поиска

Содержание SITRANS RD300

Отзывы:

Siemens SITRANS RD300, Руководство по эксплуатации, Страница: 108 / 110

Результаты поиска

Содержание SITRANS RD300

Отзывы: