manualshive.com logo in svg

Siemens SITRANS FUE950, Руководство по эксплуатации, Страница: 18 / 72

Поделиться
Скачать
Siemens SITRANS FUE950 Скачать руководство пользователя страница 18

Installing/Mounting 

 

4.3 Application settings 

Installation safety precautions 

 

WARNING 

 

In applications with working pressures/media that can be dangerous to people, 

surroundings, equipment or others in case of pipe fracture, it is recommended that special 

precautions such as special placement, shielding or installation of a security guard or a 

security valve are taken when the temperature sensors are mounted. 

 

4.3

 

Application settings 

Check of application settings 

●  Application and flow meter installation place 

Application type and flow meter installation place can be checked via order code on 

device type label. 
 - Calculator district heating, flow meter in return line (cold pipe) 7ME3470-xxAx-xxxx  
 - Calculator district heating, flow meter in forward line (warm pipe) 7ME3470-xxBx-xxxx  
 - Calculator chilled water, flow meter in forward line (cold pipe) 7ME3470-xxCx-xxxx  
 - Calculator chilled water, flow meter in return line (warm pipe) 7ME3470-xxDx-xxxx  
 - Calculator combined cooling/ heating, flow meter in forward line (warm pipe by heating) 

7ME3470-xxEx-xxxx  
 - Calculator combined cooling/ heating, flow meter in return line (cold pipe by heating) 

7ME3470-xxFx-xxxx  

●  Pulse input setting 

Calculator pulse input setting must fit flowmeter pulse output setting (e.g. ultrasonic 

flowmeter type SITRANS FUE380). Check both type plates for settings. 

●  Pt sensor type. 

Observe information of temperature sensor installation.  

●  Max. flow rate. 

Max. flow rate for energy calculator must not be exceeded. 

 

SITRANS FUE950 

16

 

Operating Instructions, 01/2010, SFIDK.PS.022.F4.02 

Содержание SITRANS FUE950









































































Отзывы:

Нет отзывов