Siemens SITRANS FUE950 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 72

Siemens SITRANS FUE950 Скачать руководство пользователя страница 15

Description

3.3 Design

The separate flowmeter for the input of volume pulse can be installed in hot or cold line.
Hot line is pipe with higher media temperature. In heating systems called forward line.
Cold line is pipe with lower media temperature. In heating systems called return line.
In cooling applications forward/return lines are the other way around.

3.3

Design

Display and push button

SITRANS FUE950 has an easy-read 7 digit LCD display with associated pictograms for

various functions. As display has been designed for several applications, figures/symbols not

used for normal district heating applications will appear in display.

Figure 3-4

SITRANS FUE950

Energy calculator has a SIMPLE OPERATION push button and provides user-friendly

control of various display menu loops.
Display will always be configured for a specific application, and for selected display settings.

In normal operation menu loop, display will show cumulative current energy values.
Integrator has an IP54 plastic housing designed for wall or panel mounting. Housing comes

with prepared rubber gaskets cable entries for fast and easy installation.

Temperature sensor set

Temperature sensor set is designed for use with Siemens energy calculator type SITRANS

FUE950 for measurement of energy consumption in a district heating net.
To ensure accurate measurement of temperature difference according to MID (EN 1434)

sensors are delivered as matched pairs.
Sensor sets can always be delivered with MID (EN1434) approval for multiple-purpose

applications in heating applications.

SITRANS FUE950
Operating Instructions, 01/2010, SFIDK.PS.022.F4.02

13

«
...
13
14
15
16
17
...
»

Содержание SITRANS FUE950









































































Отзывы:

Нет отзывов