Siemens SITRANS F FUE380 Скачать руководство пользователя страница 32

Страница: 32 / 102

5.2

Compact system

Connect the compact flowmeter using the following steps.

Connecting battery (battery-powered versions and mains-powered versions with back-up battery)

Plug in male battery plug. Ensure that the wire is inserted into the small channel leading from

plug to battery.

Preparing connection

Remove protection cover carton from the terminal box.

Connecting power supply cable (mains-powered versions only)

WARNING

Power supply requirements
Make sure the power supply requirements stated on the nameplates are met!

WARNING

Wire insulation
The insulation between the connected mains supply and the low voltage supply for the

flowmeter must be rated with at least double or reinforced insulation at mains voltage.
For field wiring installation: Ensure that the National Installation Code of the country in which

the flowmeters are installed is met.

Note
Conductor terminal
The wire size for the output terminals are AGW24 to AGW14 or 0.205 mm

to 2.080 mm

Connecting
5.2 Compact system

FUS380/FUE380

Operating Instructions, 09/2016, A5E00730100-AB

Содержание SITRANS F FUE380







































































































Результаты поиска

Содержание SITRANS F FUE380

Отзывы:

Siemens SITRANS F FUE380, Руководство по эксплуатации, Страница: 32 / 102

Результаты поиска

Содержание SITRANS F FUE380

Отзывы: