background image

 

Siemens Building Technologies

 

 

Fire Safety & Security Products 

 

03.2009

 

 

Contents 

1

 

Introduction .............................................................................................5

 

2

 

Safety .......................................................................................................6

 

2.1

 

Target readers...........................................................................................6

 

2.2

 

Work safety information ............................................................................6

 

2.2.1

 

General information...................................................................................6

 

2.2.2

 

Transport...................................................................................................6

 

2.2.3

 

Setup.........................................................................................................7

 

2.2.4

 

Installation .................................................................................................8

 

2.2.5

 

Service and maintenance .........................................................................8

 

2.3

 

Meaning of the written warning notices ....................................................9

 

2.4

 

Meanings of the hazard symbols ..............................................................9

 

3

 

Directives and standards .....................................................................10

 

4

 

Overview SISTORE AX devices ...........................................................11

 

4.1

 

SISTORE AX4 Lite V2.0 .........................................................................11

 

4.2

 

SISTORE AX8/AX16 250/100 V2.8 ........................................................11

 

4.3

 

SISTORE AX8/AX16 500/200 V3.6 ........................................................12

 

4.4

 

SISTORE AX HDD extension kit (SATA)................................................12

 

5

 

Technical check ....................................................................................13

 

5.1

 

Verification of primary HDD ....................................................................13

 

5.1.1

 

Config issues?.........................................................................................14

 

5.1.2

 

Normal booting?......................................................................................14

 

5.1.3

 

Message displayed? ...............................................................................14

 

5.1.4

 

Booting without HDD?.............................................................................14

 

5.2

 

Verification of secondary HDD................................................................15

 

5.2.1

 

Normal booting?......................................................................................15

 

5.2.2

 

Booting without HDD?.............................................................................15

 

6

 

Installation and replacement of hard disk drives ..............................16

 

6.1

 

Replacement of the primary HDD in SISTORE AX4 Lite V2.0 ...............16

 

6.2

 

Replacement of the primary HDD in SISTORE AX8/AX16 250/100 
V2.8 .........................................................................................................19

 

6.3

 

Installation of the extension HDD in SISTORE AX8/AX16 250/100 
V2.8 .........................................................................................................22

 

6.4

 

Replacement of the primary HDD in SISTORE AX8/AX16 500/200 
V3.6 .........................................................................................................25

 

6.5

 

Installation of the extension HDD in SISTORE AX8/AX16 500/200 
V3.6 .........................................................................................................28

 

6.5.1

 

Installation of  the 1

st

 additional hard disk ...............................................29

 

6.5.2

 

Installation of the 2nd additional hard disk underneath the CD/DVD 
drive ........................................................................................................31

 

7

 

Functional test.......................................................................................34

 

7.1

 

Preconditions ..........................................................................................34

 

7.2

 

Test procedures ......................................................................................34

 

8

 

Appendix................................................................................................35

 

8.1

 

Troubleshooting ......................................................................................35

 

8.1.1

 

SISTORE AX4 Lite V2.0 .........................................................................35

 

8.1.2

 

SISTORE AX8/AX16 250/100 V2.8 and SISTORE AX8/AX16 
500/200 V3.6...........................................................................................35

 

8.1.3

 

SISTORE AX RAS ..................................................................................36

 

8.2

 

Packaging for returning the HDD ............................................................37

 

9

 

Disposal .................................................................................................38

 

Содержание SISTORE AX









































Отзывы: