Siemens SIRIUS Series Скачать руководство пользователя страница 68

Страница: 68 / 182

Installation/Removal

8.2 Removing the SIRIUS 3RA6 compact starter and AS-i mounting module

SIRIUS 3RA6 Compact Starter

System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

8.2.3

Removing the compact starter from a SIRIUS infeed system for 3RA6

Requirements

●

Screwdriver with max. diameter of 7.5 mm and minimum shaft length of 100 mm for

releasing the compact starter

●

The compact starter must be switched off (actuator set to OFF position).

CAUTION

Danger, high voltage!
There is a risk of the compact starter getting damaged if it is switched on (i.e. actuator in

READY position) when you remove it from the infeed system for 3RA6.

Make sure that the compact starter's actuator is set to the OFF position before you

remove the compact starter from the infeed system for 3RA6.

Procedure

For servicing purposes, the compact starter can be removed from the infeed system while

the system is live but at zero current.

Note
The fact that the SIRIUS infeed system for 3RA6 features permanent wiring means that

there is no need to disconnect the main conductor terminals.

Step

Instructions

Image

Insert a screwdriver into the opening.

Tilt the screwdriver to the right and then

down (see arrow on enclosure lid) so

that you can push the compact starter

forwards by approx. 5 mm.

Move the compact starter forwards to

remove it from the screw-type infeed or

extension block.

Note
The 45 mm adapter for the infeed system for 3RA6 can be removed in the same way.

Содержание SIRIUS Series























































































































































































Результаты поиска

Содержание SIRIUS Series

Отзывы:

Siemens SIRIUS Series, Системное руководство, Страница: 68 / 182

Результаты поиска

Содержание SIRIUS Series

Отзывы: