Siemens SIRIUS Series Скачать руководство пользователя страница 66

Страница: 66 / 182

Installation/Removal

8.2 Removing the SIRIUS 3RA6 compact starter and AS-i mounting module

SIRIUS 3RA6 Compact Starter

System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

8.2

Removing the SIRIUS 3RA6 compact starter and AS-i mounting
module

The sections below explain how to remove the SIRIUS 3RA6 compact starter from:
●

A DIN rail

●

A level surface (screw fastening)

●

The infeed system for 3RA6

The process of removing the AS-i mounting module from the compact starter (24 V) is also

described.

8.2.1

Removing the compact starter from a DIN rail

Requirements

●

The compact starter must be switched off (actuator set to OFF position).

●

The AS-i cables must be removed.

Note
Disassemble the compact starter's main and control conductor terminal blocks before

removing it, as this makes the process easier.

Procedure

Step

Instructions

Image

Pull the device down until the lower half

can be pulled away from the DIN rail.

Pull the lower half of the device away

from the DIN rail and lift the device off

its upper edge.

Содержание SIRIUS Series























































































































































































Результаты поиска

Содержание SIRIUS Series

Отзывы:

Siemens SIRIUS Series, Системное руководство, Страница: 66 / 182

Результаты поиска

Содержание SIRIUS Series

Отзывы: