Siemens SIPART PS2 6DR5xx0 series Скачать руководство пользователя страница 2

Страница: 2 / 57

A5E03436620-AB, 01/2017

SIPART

Electropneumatic positioners

SIPART PS2 (6DR5...)

Compact Operating Instructions

Legal information
Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The

notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage

have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of

injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with

the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their

training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products

and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage,

installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any

problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Содержание SIPART PS2 6DR5xx0 series


























































Результаты поиска

Содержание SIPART PS2 6DR5xx0 series

Отзывы:

Похожие инструкции для SIPART PS2 6DR5xx0 series

Бренды по названию

Популярные бренды

Siemens SIPART PS2 6DR5xx0 series, Краткое руководство по эксплуатации

Результаты поиска

Содержание SIPART PS2 6DR5xx0 series

Отзывы:

Похожие инструкции для SIPART PS2 6DR5xx0 series

Бренды по названию

Популярные бренды