Siemens SION 3AE6113-0 Скачать руководство пользователя страница 8

Страница: 8 / 60

Transport, storage and packing

9229 0020 176 0B

2019-04-02

Transport to the

installation site

• Remove all tensioning belts and bits of fastening wood.
• Remove supplementary equipment and store safely in the packaging for later

installation.

Fig. 3

Example - two vacuum circuit-breakers

Fig. 4

Example - one vacuum circuit-breaker

Note

Material damage due to incorrect mounting of sling gear!
Using chains or steel ropes will damage the pole shells. Use only ropes, hose
sheaths or belts.
Only use the lifting eyes for sling gear.

1) Diameter of the hook cross-section max. 19 mm
2) Opening width of the hook min. 18 mm

• Hang sling gear only into the lifting eyes.
• Adapt the length of the belts so that the belts are

flush with the pole shells during transport. The pole
shells serve as stabilisation for the vertical transport
position.

• Transport to installation site or leave suspended

from crane for further work steps.

Fig. 5

Transporting

Note

Keep supplementary equipment on hand for installation.

Содержание SION 3AE6113-0




























































Результаты поиска

Содержание SION 3AE6113-0

Отзывы:

Похожие инструкции для SION 3AE6113-0

Бренды по названию

Популярные бренды

Siemens SION 3AE6113-0, Руководство по эксплуатации

Результаты поиска

Содержание SION 3AE6113-0

Отзывы:

Похожие инструкции для SION 3AE6113-0

Бренды по названию

Популярные бренды