background image

SIMOLINK Pulse Generator

02.2001

Definitions and Warnings

Siemens AG

GWE-477 764 4070.76 J

SIMOVERT MASTERDRIVES

Operating Instructions

1-1

1 Definitions 

and 

Warnings

For the purpose of this documentation and the product warning labels,
a "Qualified person" is someone who is familiar with the installation,
mounting, start-up, operation and maintenance of the product. He or
she must have the following qualifications:

  Trained or authorized to energize, de-energize, ground and tag

circuits and equipment in accordance with established safety
procedures.

  Trained or authorized in the proper care and use of protective

equipment in accordance with established safety procedures.

  Trained in rendering first aid.

indicates an imminently hazardous situation which, if not avoided, will
result in death, serious injury and considerable damage to property.

indicates a potentially hazardous situation which, if not avoided, could
result in death, serious injury and considerable damage to property.

used with the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in minor or moderate injury.

used without safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.

NOTICE used without the safety alert symbol indicates a potential
situation which, if not avoided, may result in an undesirable result or
state.

For the purpose of this documentation, "Note" indicates important
information about the product or about the respective part of the
documentation which is essential to highlight.

Qualified personnel

DANGER

WARNING

CAUTION

CAUTION

NOTICE

NOTE

Содержание SIMOVERT MASTERDRIVE Series



























Отзывы: