Siemens SIMOTION P Series Скачать руководство пользователя страница 85

Страница: 85 / 138

Application planning

4.8 Mounting positions and fastening

SIMOTION P350-3 and Panels
Manual, 05/2009

4.8

Mounting positions and fastening

4.8.1

Installation guidelines

Before installing the device, read the following general notes relating to installation.

WARNING

Danger, high voltage
Isolate the power supply to the control cabinet before opening it. Ensure that the power to

the control cabinet cannot be turned on accidentally.

●

Ensure that the protective contact socket of the building installation is easily accessible

and that there is a mains disconnect switch in control cabinet installations.

●

Position the screen in an ergonomic position favorable to the user. Choose a suitable

installation height.

●

Position the screen so that it is not subject to direct sunlight or other strong sources of

light.

●

DVD drives are susceptible to vibration. Shocks during operation can lead to the loss of

data or damage to the drive or data carrier. Burners and DVDs are not suitable for

continuous operation.

●

Applies to devices which are installed in swivel arm housings: Avoid rapid or jerky

movements of the swivel arm during operation. The ensuing forces could lead to possible

irreversible damage of the hard disk.

●

The device with DC power supply is considered an open piece of equipment where the

voltage supply is concerned. Therefore, make sure that the control cabinet fulfills the the

requirements of a fire-proof housing.

●

Provide adequate volume in the control cabinet for air circulation and heat transport.

Keep 5 cm clearance on all sides between the device and the control cabinet. This

clearance is increased accordingly with connection cables.

●

Do not allow the maximum air intake temperature to exceed 45° C. The temperature

measured at a distance of 5 cm from an air inlet is decisive. The maximum air intake

temperature must be accounted for especially when sizing closed control cabinets.

●

The minimum distance between the device and the housing is 5 cm on the air output side

at the ventilator.

●

Position the device so that the air vents of the housing are not covered up following

installation.

●

Ensure there is enough free space in the control cabinet to allow the sheet metal cover to

be removed. You will otherwise have to remove the device from the control cabinet or

swivel arm when replacing the memory or the back-up battery.

Содержание SIMOTION P Series











































































































































Результаты поиска

Содержание SIMOTION P Series

Отзывы:

Похожие инструкции для SIMOTION P Series

Бренды по названию

Популярные бренды

Siemens SIMOTION P Series, Руководство пользователя

Результаты поиска

Содержание SIMOTION P Series

Отзывы:

Похожие инструкции для SIMOTION P Series

Бренды по названию

Популярные бренды