Siemens SENTRON 3WA Скачать руководство пользователя страница 59

Страница: 59 / 82

PROFINET IO

6.3 Metering values, addressing und data traffic

3WA Air Circuit Breaker Communication
System Manual, 11/2021, 92310000004-02

Free selection of modules

The cyclic data can be configured in any way from the available modules. You can find more

information in the table provided in the section "Modules that can be plugged in for the

project" above.
Further individual modules without property bytes are available in addition to the basic types.

Basic type 1

Basic type 1 was implemented according to the LVSG profile of the PROFINET user

organization (PNO) and comprises four data blocks. These are preassigned such that they are

primarily suitable for use with a 3WA circuit breaker without metering function. The most

important currents of the phases are transferred.
The predefined data blocks cannot be modified.

Byte

Definition

Default

0 / 1

Data block 1

Current in phase 1 (u16)

2 / 3

Data block 2

Current in phase 2 (u16)

4 / 5

Data block 3

Current in phase 3 (u16)

6 / 7

Data block 4

Max. current in phase under highest load (u16)

Basic type 2

Basic type 2 was implemented according to the LVSG profile of the PROFINET user

organization (PNO) and comprises six data blocks which are preassigned for a 3WA circuit

breaker with metering function. Here only the average voltage values are transmitted.
The predefined data blocks cannot be modified.

Byte

Definition

Default

0 / 1

Data block 1

Current in phase 1 (u16)

2 / 3

Data block 2

Current in phase 2 (u16)

4 / 5

Data block 3

Current in phase 3 (u16)

6 / 7

Data block 4

Max. current in phase under highest load (u16)

8 / 9

Data block 5

Current in neutral conductor (u16)

10 / 11 Data block 6

Active energy import (u16)

Содержание SENTRON 3WA



















































































Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды

Siemens SENTRON 3WA, Системное руководство

Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды