Siemens SENTRON 3WA Скачать руководство пользователя страница 58

Страница: 58 / 82

PROFINET IO

6.3 Metering values, addressing und data traffic

3WA Air Circuit Breaker Communication

System Manual, 11/2021, 92310000004-02

Control bytes

The control bytes for controlling the circuit breaker are always two bytes long. With these

control bytes, you can:

•

Open/close the circuit breaker

•

Acknowledge tripping events

Setting the outputs is edge-triggered. It suffices to set the corresponding bits for 0.5 s. After

this, these control bits must be reset to avoid subsequently triggering any undesired actions.
The table below contains a description of the control bytes:

Byte

Bit

Value

3WA circuit breaker

0 / 1

0 … 3

Commands to close/open the circuit breaker

Not defined (no action)

Circuit breaker open (opening of main contacts)

Circuit breaker closed (closing of main contacts)

Not defined (no action)

–

Acknowledge and reset currently active trip indication

–

Not used

–

Not used

–

Not used

–

Not used

–

Not used

n + 1

–

Not used

–

Not used

–

Not used

–

Reset all minimum/maximum value logs (except temperature)

–

Reset minimum/maximum logs for temperatures

–

Not used

–

Not used

–

Not used

Содержание SENTRON 3WA



















































































Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды

Siemens SENTRON 3WA, Системное руководство

Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды