Siemens SENTRON 3WA Скачать руководство пользователя страница 45

Страница: 45 / 82

Modbus TCP

5.9 Configurable Modbus TCP port

3WA Air Circuit Breaker Communication
System Manual, 11/2021, 92310000004-02

5.9

Configurable Modbus TCP port

It may be necessary to change the number of the TCP port due to applications or to ensure

cybersecurity. The TCP port number for Modbus TCP connections can be configured with the

SENTRON powerconfig configuration software or as a data point. The default value 502 can

be changed accordingly.

Note

Changing the default port can make it difficult to find a 3WA circuit breaker in the network

using the default search algorithm (e.g. in the SENTRON powerconfig configuration

software).

5.10

System time with SNTP

5.10.1

Requirement

The Simple Network Time Protocol (SNTP) can be used to set the system time of the 3WA

circuit breaker. SNTP is a simplified version of NTP and automatically sets the system time

with the help of NTP servers (time servers).

Содержание SENTRON 3WA



















































































Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды

Siemens SENTRON 3WA, Системное руководство

Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды