Siemens SCALANCE XR524-8C Скачать руководство пользователя страница 81

Страница: 81 / 100

Technical data

8.3 Technical specifications of the SCALANCE XR552-12M

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

Technical specifications
Permitted ambient conditions
Operating temperature

Operation without filter pad and

without SFP+ LH transceiver

0 to +60 ℃

Operation with filter pad and

without SFP+ LH transceiver

0 to +55 ℃

Operation with filter pad and

with SFP+ LH transceiver

0 to +50 ℃

Ambient temperature

During operation up to 2000 m

40 ℃ to +65 ℃

During operation up to 3000 m

40 ℃ to +50 ℃

During storage

40 ℃ to +70 ℃

During transportation

40 ℃ to +70 ℃

Relative humidity

During operation at 25 ℃

≤ 95%, no condensation

Design, dimensions and weight
Weight (basic device without media

modules)

10 kg

Degree of protection (with closed

service panel)

IP20

Dimensions without brackets for

19" rack mounting (W x H x D)

446 x 133 x 305 mm (3 height units)

Installation options

•

19" rack mounting

•

Desktop operation

•

Four-point mounting

Design of the mounting bracket for use on ships
Dimensions without brackets for

19" rack mounting (W x H x D)

60 x 130.5 x 18.3 mm (3 height units)

Plate thickness

1.5 mm

Bending radii

1.5 mm

Surface of the housing

Stainless steel X6CR17

Mean time between failure (MTBF)

•

Basic device without media

modules

•

at 40 °C ambient temperature

> 15.7 years

Note
ISO tolerance and punching burr
For dimensions without tolerance details, the general tolerances "medium" acc. to DIN ISO

2768 apply. No punching burrs are permitted.

Содержание SCALANCE XR524-8C





































































































Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды

Siemens SCALANCE XR524-8C, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды