Siemens SCALANCE XR524-8C Скачать руководство пользователя страница 42

Страница: 42 / 100

Assembling

4.8 Mounting power supply units

SCALANCE XR-500

Operating Instructions, 05/2014, A5E03275845-05

4.8

Mounting power supply units

4.8.1

19" rack mounting of the PS598-1 power supply unit

Notes on 19" rack mounting of the PS598-1 power supply unit

The PS598-1 was developed specifically for use with the SCALANCE XR528-6M and

SCALANCE XR552-12M devices. This power supply unit can be mounted directly above or

below a SCALANCE XR-500 since the ventilation slits are on the sides of both the basic

device and the power supply unit.

CAUTION

Risk of injury if subjected to irregular mechanical strain
The device must be mounted in the rack so that even if there is irregular mechanical strain,

no dangerous situation can result.

Procedure

Figure 4-4

19" rack mounting of the power supply unit

To mount the PS598-1 power supply unit in a 19" rack, follow the steps below:
1.

Secure the two mounting brackets with four screws each (M3 x 6 supplied with the

product) to the side panels of the power supply unit

①

The maximum tightening torque for these screws is 0.5 Nm.

Screw the PS598-1 power supply unit to the 19" rack

②

Содержание SCALANCE XR524-8C





































































































Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды

Siemens SCALANCE XR524-8C, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды